Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello!
I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption...
Hi,
We are currently testing DFU upgrades on Android. In my current setup I have two different phones, a Sony one running Android 8 and a OnePlus running Android 10.
The...
We have a device (in central mode) initiating a secure connection to a peripheral (slave) via the usage of `pm_conn_secure(conn_handle, false)`. This results in a `PM_EVT_CONN_SEC_SUCCEEDED...
Hi All,
I want to convert analog input into digital using SAADC on nRF52840 DK. After that to push the SAADC output through the Bluetooth (nRF connect bluetooth mobile application...
Hi，
Recently，i try to install the tool chain of nrf connect sdk as the instruction as guide。After installed west，then run command “west update”，but got an error：
Can...
Hi ... folks
I am using nRF52832 and analog IR sensor , Working with the example saadc . In this case , i am giving the IR sensor input voltage as 5v , analog pin 2 .I am...
Hi,
I am using NRF52832 Development board, SDK(nRF5_SDK_15.3.0_59ac345) from this i am using (/nRF5_SDK_15.3.0_59ac345 (4)/examples/ble_peripheral/ble_app_uart) example...
Is the nRF52 RSSI block of the RADIO module based on the entire 2.4GHz ISM band, or can it be configured to only measure a given 1-2MHz band of interest? According to the...
I'm using the serial library for the first time. What are the advantages/disadvantages of using IRQ and DMA? How should FIFO queue and buffer sizes be chosen?
Hi,
I am using the following code to implement a millisecond timer read function. In main, while loop, I do nothing but run a 1ms delay and measure the time in mill second...
Hello, I'm a researcher.
I wanna use Bluetooth CTE(Constant Tone Extension) feature with 1-antenna TX + 1-antenna RX.
I have seen some articles that nRF52840 DK does...
I am using nRF52832 with SDK 16.0.0. I have a simple application that uses SAADC and BLE. It reads values from three channels AIN0, AIN2 and AIN4 and sends them via BLE every...
hi all,
we're developping an application to control the frequency and the duty cycle of a pwm signal throuth ble .
firstly we have built both the functionalities separatly...
So, this library in the SDK looks pretty much exactly what I'm looking for. basic data record storage functionality with a focus on safe record writing under battery power...
