Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
So I am trying to store a few configuration parameters in flash. I am using nrf_fstorage for that. so before storing the parameters, I am erasing the flash but, it hangs at...
I am using the chip NRF52840 ,the board is powed by a battery, and I program the firmware by using the JLINK,then I unplug the JLINK and waiting the system to go into sleep...
I'm working on a project using the nRF52840 that will have a central device with an NFC reader and up to three peripheral devices with an NFC tag. The goal is to have an LED...
We have already developed firmware for our product using SDK nRF5 SDK v14.2.0 with Soft device S132 V5.0.0. For the new product development, we plan to use the Soft device...
Hello all,
We are trying to use Background DFU.
We are able to trigger using "background_dfu_validate_trigger" and "background_dfu_process_trigger". Process the init packet...
Hi,
I'm looking to connect DAC 5504 ( By AD ) to my NRF52840 based design.
I was wondering if a similar work has been done before ? I can use a good reference code
...
Hi!,
Im curious of what the below module (U34) does within the GPS circuit?
Also, what does the MAGPIO0 "55" do?, can I use one of the GPIOS for enabling the GPS?...
Hello All,
I created a BLE service (relay service) to be able to turn ON or OFF a relay switch. The relay switch hardware is attached to Adafruit Bluefruit Feather (nRF52832...
Hi,
As i know that the nRF52840 DK having thread, Ant and zigbee supports. Till now we can tested examples using the DK's only. Now am eagerly waiting to know that is...
Hi.
I use SDK15.3 (PCA10056 NRF52840) USB MSC example.
i can enumerate disk, creat file and delete file. but i can not edit file.
When I edited the file, re-plugged...
Hello! i am working with nrf5-ble-mpu-data-ready-interrupts example from github, I defined twi, could compile it without errors. But the case it, it doesn't advertise and...
Hi,
I'm trying to get my NRF52840 to minimum current in sleep, but got stuck around 440 uA. Reading through the various posts about sleep current for this type of device...
Hello,
I have created a service with three characteristics in which the 1st and 3rd characteristics have all the three Notify, read, write properties. The second characteristic...
Hi!
I'm try restrict device connections with whitelist.
Code based on examples/ble_peripheral/ble_app_hids_mouse.
My problem - any devices can bond and connect even...
Hi,
Using power profiler I measured power consumption of BLE mesh and it gives ~12mA.
What I would like to know is why the device is consuming more power during scan....
