Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
After (accidentally) entering bootloader mode on my nRF51 DK (PCA10028), the device doesnt show up either in the device manager or using nRFgo Studio (both not normally...
I bought Nordic nRF52840-DK at an electronics store in Taiwan. J-link cannot be detected when connecting to a computer. I bought two pieces nRF52840-DK. One of them can be...
I've been having lots of issues putting the example projects on the NRF9160 dev kit. It builds without errors, connects to J-Link, but sometimes fails on the download step...
I'm unable to program a nrf52840 dev kit (BMD340 dev kit) using the attached hex file combination of Bootloader and softdevice. Both bootloader and softdevice can be programmed...
Why do I get the folowing error with mbedtls when doing "west update"?
Possibly related issues: * devzone.nordicsemi.com/.../west-update-blocks-and-fails-on-mbedtls (Didn...
Hello All,
I loaded the last FW version (mfwnrf9160100) in my nRF9160 SDK using nRF Connect Programmer and looks fine.
However, the Reset button or AT commands are not...
How would I take a NRF51 Dongle that has the stock firmware from nRF Connect and communicate/send commands to it over something like PuTTY? I've tried sending AT Commands...
Hi
configure as:
ROM start: 0x26000
RAM start: 0x20002218
when I download application software , it pops up following error.
I'm using keil uVison version 5...
Hello! I am doing some development with pc-ble-driver-py and ran in to some unexpected behaviours when reading characteristics. I have been modifying the nus_collector.py...
Hi
In the last few months I posted a question about RTOS and softdevice and I need to read the answer again but I am struggling to find how to do that
Look forward to...
Mesh core is aware of the total length of DFU package. Why Application hasn't this data?
DFU packet DFU start has data field Firmware length (see here ) Mesh data structure...
Hi,
as my project moves forward I've switched to development of central board. In addition to space restrictions the board is promising to be a resource hog. A 2500+ mAh...
Hi,
I am using SDK13 and have noticed some critical issue with peer manager while bonding. The problem is that after performing dfu of my device (which was bonded with two...
Hello, I'm developing application starting from blinky example extracted from nRF5_SDK_15.3.0_59ac345 SDK. I see (using nRF Connect) that the connection result as "unencrypted...
