Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
I think, I found a missing configuration in the QSPI driver for the nrf53 in nrfx_qspi.c. I've stumbled off this, while I was trying to configure MCUboot for the external...
We are working on a Zigbee-based network coordinator using the nRF52840. Our end device is connected to the coordinator, but when the end device leaves the network, it sometimes...
I am trying to understand why my spi_dt_spec doesn't get the right pins when I use the SPI_DT_SPEC_GET ( DT_NODELABEL (kx122_spi), SPI_OP, 0 ); macros. I tried to expand it...
Hi,
I'm using an nRF9160DK v1.0.1 (2021.26) for developing an application using the virtual COM ports for logging. All of a sudden, I saw that my console showed that the...
Hi ,
I am trying to integrate LSM6DSL to BL5340 module(laird connectivity) through SPI but I am getting failed on initialization. I am noob to NRF so could someone please...
Hi all,
I've build my own board with nrf9161 LACA, so for now I've tried to create my own board, for the moment I'm just trying to pilot my 3 leds. I've follow dev academy...
Hi, I'm building an application that will use the nrf9160 as a middle man for a websocket connection that becomes a uart connection on the main processor. Thus I want to receive...
Hello there! I am working on a central-peripheral connection, where sometimes the central is not receiving notification(s) from the peripheral. The central then asks for a...
Completing the nRF Connect SDK Fundamentals in the DevAcademy, I stumbled across this question:
Why is true not a valid answer here? Running gpio_pin_set_dt(&led, true...
Hi,
I was following the beginners tutorial and things were fine till i reached the section to create a project from scratch. I was able to build this project as well.
...
Hello,
I'm curious if there is a dependency to use the same Bluetooth module to perform OTA. If I created my own custom board, would I need to use an identical Bluetooth...
I have followed the procedure given at following url https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/create_application.html and created a application(based...
Hello,
I am working with the Signetik M1-N1 module, which is using the nRF9160 chip, as well as the DEV-M1-N1 breakout board, for evaluation and development:
Since this...
Hi,
I am working on a project that uses nrf52833 as one of I2C master to communicate with few I2C slave devices. Meanwhile there is another MCU (stm32H7) on the same bus...
