I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Greetings,
We are attempting to install the nRF Sniffer program onto our nRF52833 DK as directed in the Nordic instructions. We've installed the nRF Connector S/W as well...
Hello All,
We are in the evaluation phase to implement openthread network in our gateway using nRF52840 as NCP device.
We require to have the number of end-device supported...
Hi,
I used to have a URL link for checking ibasis SIM card, such as devices, balances, etc. Now, I cannot find. My SIM card is from Nordic, so the login for ibasis account...
Hi Dev Team,
I am building an application wherein I need to send commands from the Cloud to a Thingy91 device. I tried out the cloud_client sample and I was able to send...
I have seen this problem posted several times in these forums but none of the existing solutions sit right with me.
I have an NRF52840 (using a UBlox BMD-340 dev board...
Hi Dev Team,
I have an application wherein I am publishing my sensor data every hour through MQTT using a Thingy91.
I am storing my sensor data value in a JSON format...
Hi,
I am trying to implement protobuf for my application. I have seen that nano-pb library is there in SDK file. I want to use it in BLE-UART communication. How to do with...
Hello,
I am using RFX2411N RF amplifier in my hardware design. I chose nRF52832 as an MCU. In nRF52832 datasheet, it is mentioned that the pins from P0.22 to P0.31 have...
Hi,
We are currently developing a Zigbee network based on nRF52840.
One of our devices was specially designed to contain 8 endpoints. But when an active ep request is...
Hi,
I'm using the BLE_app_interactive example as a starting point for my prototype (with SDK_17.0.2 and SoftDevice s132 ). I am using nRF52DK to read and write data from...
Hi
Im trying connect two peripheral devices through UART
The example project I used is "examples/peripheral/uart"
But i trace the code, it seems that the driver layer...
Hello,
I've been using nrfx UARTE driver on the nrf5 15.2.0 SDK on a nrf52832 and nrf52840 SoC and noticed that during the boot-up the first byte being sent is 0xFF.
Is...
Can I remove resistor R29 (ENCHG) on the ADP536 to disable the charging function and plug my 3.3V supply into the battery connector?
i.e. use the ADP536 for the power management...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
