I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi!
I've just received a nRF9160 DK.
I've installed nRF Connect v2.6.2 and LTE Link Monitor.
I select the device (3 serial ports are shown). I press reset button and...
When working with a custom board with nRF52840 chip, I'm having serious problems with SWD connectivity. In many cases JLinkExe can't connect to target at all. I did some measurements...
Hi there!
I'm trying to simulate a peripheral with a PCA10040 and nRF Connect for Desktop.
I've made the Server Setup, applied to the board and started advertising - everything...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Initially I was in assumption that once...
Hi,
Is there a table / .xls available for ALL nordic parts to date?
I'm trying to find all options with +8 dBm TX Power & WLCSP package. (no need for usb)
Hi, I'm trying to get the nrf_stack_guard and nrf_mpu libraries to catch writes past the end of the stack. My stack is 8kB in size (0x2000E000-0x20010000). This is the log...
Hi,
I'm working on the custom board using nrf52832 chip and have performed the secure bootloader using ble on the custom board.
I have made these changes so far on the...
We want to connect provisioned node to multiple mobile application over same mash network (Note: We are trying to give access to multiple user(using multiple mobile) to connect...
Hello!
This may be the wrong place to ask, but I am in search of a gateway (off the shelf or a reference design), that incorporates 802.15.4 through the nrf52840, cellular...
Hi,
I just have a small question: say I have two models, both with publish timeout intervals configured. After some time, one model's publish timeout handler is called....
Hi to everybody,
I'm developing over nRF5 SDK v. 3.2.0 a Zigbee node in router role. In my network I've four of my nodes plus several commercial led light driver and a coordinator...
Hello!
I am setting up SEGGER on my mac. Completed all the steps in Getting Started Assistant. But in the last step at "Set up a project in SEGGER Embedded Studio" where...
Hi,
I am evaluating a project where I want to run light switch on nrf52840. This is supposed to support mentioned protocols - BLE Mesh, Thread and Zigbee, but NOT concurrently...