Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi
We are going to use the Taiyo Yuden Evaluation Board - EBSHJNZWZ.
As i understand, the board firmware used the Nortic SoftDevice S132
The question is :
May i...
Hello,
I'm trying to compile an example of nRF52_SDK_1 but I get this error:
make
Makefile:150: Cannot find include folder: ../../../config/receiver_pca10040
Makefile...
Hello,
I've been reading over different examples and questions on the Nordic Developer Zone but still have some questions about multiple SAADC channels.
1 - If I initialized...
I've been developing an application on the nrf51 DK based on the ble uart application and it's been working fine. I've ported it to a custom board running at 1.8V and attached...
Greetings -
I am using (the slightly out-dated) 12.3 SDK with a nRF52840. I'm also using s132 as my softdevice.
As I've been slowly reducing my RTC interrupt frequency...
Hi,
I want to activate readback protection on nRF51822, in a simple project without bootloader without softdevice.
My compiler is GCC and the const uint32_t UICR_RBPCONF...
Hi. I don't understand how to build nrf_drv_saadc.c with gcc. I'm getting this error in the EVT_TO_STR() macro:
Compiling file: nrf_drv_saadc.c
In file included from ...
Hello,
I'm going to use nrf52-ble-image-transfer-demo-master for my application.
But demo used other way with cpp code for configuring nrf52832 interfaces(spi, twi, gpio...
Hello Folks,
Nice to see an active developer community out here! I ran into some issues last night which I hope could be resolved. We procured nRF52840 SoCs and have developed...
Hi all,
i'm new to BLE in general, I found this chip (nrf52832), which suits my uni project.
However, I don't have much knowledge about this technology. therefore, im...
Hi everyone,
I would like to test the capabilities of nRF52840. I understand that it should be capable of higher throughput (x2), increased broadcast capacity (x8), and...
Hi,
I need solution for modbus interface.
My One Central connected with Modbus Server App and 8 slave connected with each peripheral.
which SDK and Mode used for this...
Hi,
I just read Understanding NRF_ERROR_BUSY and wanted to know if this is true for the S132 V5 softdevice.
So each connection can queue one system Tx packet and one...
