Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi,
I want to start TIMER1 by a GPIO_TE.
When the program enter the TIMER1_IRQHandler(), I want to disable the ppi.
And when the program leave the TIMER1_IRQHandler(),...
Hi,
I'm on OSX, and I'm having problems where the first service calls I make on my own device fails but work fine on the second generation Nordic development board.
...
In the changelog for 7.1.0 is says:
"This version deprecates all previous 7.x.x versions"
But in the compatibility matrix, it seems like 7.1.0 is only supported by revision...
i had used flash manager that is in BLE libraries to store datas for persistent storage. but it seems can't work after i enable the softdevice. so i try to use pstorage, i...
Hi support !
In my current application, I use nRF24L01+.
I want to change this nRF24L01+ for a nRF51422 to add BLE connectivity.
So, I've started my development with...
I'm using SDK 7.1, PCA10028 eval board, SD110 7.1, MCP 3.6.0.8331
I have 2 characteristics, and both are 32 bytes long. When I try a "Write Long" from the MCP a
BLE_EVT_USER_MEM_REQUEST...
Hi,
Merry Christmas!
I have a question about pstorage_store.
Actually, I want to store some data in the memory. Each piece of data has its own size (between 1 byte to...
Can I config AIN0 and AIN7 as the input pins of ADC, and config P0.01 and P0.02 as TWI, and config P0.03 and P0.04 as GPIO?
Or I must config ALL AIN PINS as ADC?
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi,
I've followed the steps mentioned in this thread devzone.nordicsemi.com/.../ and everything seemed to work fine. I've successfully uploaded "nrf51822_beacon_app.hex...
Hi.
I read in the sdk documentation, there is a library to use MPU-6050.
So i try to find it but I did not succeed.
i want to read data from 6050 and send this data with...
Hello.
I want to use nRF51422 chips to make some kind of mesh network using raw radio stack (NRF_RADIO) with my own protocol on the top of it. In reference manual there...
Hi,
I am a new comer to the nRF8001.
I am using Redbear Blendmicro (nRF8001) for my project.
I have wrote a apps to scan my Blendmicro(s) and acquire their RSSI value...
