Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hello,
I am working with a thingy9160 to connect to an MQTT broker using TLS.
I have run into an issue where the MQTT connection is disconnected with error code #XMQTTEVT...
Hi,
I have a nrf52833 with MCUBoot and BLE, I am using NCS v3.0.1.
I need also a custom NVS partition to store user data, so i create a data_partition for this purpose...
Hello,
I'm trying to build a Zephyr module that manages some features for a specific board (an SDK for that board). In it, I would like to enable the IPC devices in the...
I am testing data transfer from a microcontroller to a host PC using USB CDC ACM on the nRF5340. Right after powering on the microcontroller, only the first packet takes longer...
hi support team,
do we have any samples on how to show radio statues to gpio? when radio is on, gpio is set to high, and radio is off, gpio is set to low.
waht i can think...
Hi everyone,
I'm in the middle of a project and am starting to run out of available GPIOs.
To save a pin, I was wondering if it's possible to use a single GPIO (for example...
As a detour to getting DFU working for my existing project, based on nRF54L15, it was suggested in a previous ticket that the issue might be with my custom board folder, and...
Hello,
I would like to ask if it is possible to print the status of individual parts of memory on nRF7002-DK while the program is running? So far, I have managed to print...
I am using ncs to develop for NRF54L15. It runs fine on the development kit DK, but it doesn't work properly on my own hardware board. My program always fails to simulate...
Good morning,
I have tried to do the exercise 6 from the nrf-connect-sdk-intermediate course, my nRF9160 devKit can connect to nRF Cloud and download the new firmware. When...
Hello, We are currently evaluating the use of nRF9131 ICs for a mobile DECT NR+ usecase, in which we want to use the position in space of the different participants. Given...
We want to encode audio to LC3 format before we pass it to nrf5340 over USB. Because we know the processing power of nrf5340 is limited. Do you have any support for this?...
Description:
We're using GRTC on the nRF54L15 to implement RTC calendar functionality in our project. During development, we observed the following behavior:
When...
I am developing a Zigbee sensor device based on the nRF52840. I have based my firmware on the "Thingy:53: Zigbee weather station" sample. This means it is a Sleepy End Device...
