I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi there,
I've recently purchased a nrf9160dk to evaluate. I've got some demo code going connecting via LTE and chatting to my AWS server via TCP and that's all going well...
Is there any SPI examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
I want to know the best way to handle time-consuming processes.
I am using an external module used for AT commands via UART. It is necessary to judge the success or failure...
Hi,
Tools used for programming
I am trying to program my custom Adaruit nrf52832 board through NRF connect Programmer.
I am using Nordic nrf52DK to program Adafruit...
Hello,
I need to temporarily hardcode MBR_BOOTLOADER_ADDR address in the code so flash area is calculated correctly in fds.c. I have the following code in my ld file:
...
I'm having issue where after booting I can immediately do three SAADC samples as follows:
This works as expected where I get the callback immediately after the third call...
Hi Nordic,
I have decoded the advertise report below. Will you please confirm my understanding is correct.
Especially
[02] --> NUS_SERVICE_UUID_TYPE
[01] --> BLE_UUID_NUS_SERVICE...
Hello,
I am using the ble_app_beacon example on a nRF52840 dongle.
Without changing the code I am able to load and use it on my dongle.
Now, I am trying to add some...
Hi , i have attempted to build an spi read and write function for the BMI085 imu sensor and I seem to be having a problem with the read function. i have used the spi example...
Hi i'm studying ESB in nrf52833 DK
I have a few question.
1. When a packet is sent from ptx to prx, transaction starts, and when prx receives a packet from ptx, it sends...
Hi,
I want to add ble dfu to the hid keyboard example using nRF52810. I have tried unbonded and bonded，both are not work.
By using the bonded way, I made the following...
HI,ALL:
In SDK16, 1 .as topic,when I trigger the mouse_movement_send() and the mouse_click_send() at the same time, Error occurs.
2.how to detect BLE search device sucessfully...
Dear Members,
I tried to find a file *pca10056 project for bsc_rx on ant_plus ?
Can anyone tell me where I can find that file on the SDK ?
Thanks
Visit my lab...
We use a frontend that requires four pins and the timeslot API with our own protocol on nRF52832 & nRF52840. This works fine, but for BLE to work properly we need to leave...
i have a problem with the nRF52 DK (PCA10040) I followed these instructions https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3.1.pdf and the python version is 3.9...
