Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Refer to this post ， I did the same job to change simple_on_off model into generic OnOff Model , and I could control the LED state with nRF Mesh application as well.
I have...
Hi sir,
we used nRF 52832 ESB protocol ，
use
NRF_ESB_PROTOCOL_ESB_DPL
#define NRF_ESB_MAX_PAYLOAD_LENGTH 128
bitrate = NRF_ESB_BITRATE_2MBPS
so how can I config...
My app (S130 SDK12.3; BLE with multiprotocol support where the radio session is opened before advertising) registers function sys_evt_dispatch() as per
but sys_evt_dispatch...
Hi,
I am not yet familiar with NFC and have a question about using NFC with the nRF52.
If I understood it correctly the nRF52 is a "listening device" i.e. it cannot...
Hi Nordic,
I am trying to do a time critical data acquisition in a BLE based application.
Earlier I was using software timers. But, since the software timers are not accurate...
Hi all, I have some question for ask :
I add NUS service into light switch proxy server example. And I only run nus service part (Don't run Mesh part)
when I use IOS to...
Hello All, Please help me. I have nrf52840 and added json parser which is large and nested. Json_parse fails , is there anyway to enlarge heap size?
Any feedback must be...
Hello,
I'm trying to flash wt51822-s4at using nrf52dk ( https://4tronix.co.uk/picobot2/WT51822-S4AT.pdf)
It has nrf51822 chip on board
The firmware goes through without...
Hi,
Does FDS event handler run within interrupt context ?
Can another FDS api be called from within the event handler (i.e. - calling garbage collector from within event...
I am using a three axis mems sensor and will need to computer trig functions.
If I use the math.h in the Segger Embedded Studio will it use the floating point hardware in...
In this thread https://devzone.nordicsemi.com/f/nordic-q-a/32708/bluetooth-developer-studio-plugin-for-sdk-15-0-0/126066#126066 Kenneth said there were no plans to update...
I can not debug my app with freertos and BLE if the ble is connected, but I can debug the app id the ble is disconnected, i want to debug inside the xqueue recieve and send...
I'm developing on the nrf52840PDK and I was running the cdc_acm exmaple in the SDK to observe the token exchanges between the host and the device.
In the Nordic52840 Product...
Hi all,
I have a module with nRF52832QFAAB0 IC, I'm looking for the IC revision in the compatibility matrix here.
Unfortunately I didn't find any packet variant and build...
I've run the Demo(thingy52-mesh-provisioning-demo). And it works. Now, I want to expand the function.
I 'd like to create more model(for example, sensor model for humanity...
