I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi all
When i am reading ANCS code, i have some questions. SDK 12
Question 1: when ble device are connected with ios, the pairing is wrong, how to handle validation...
I am attempting to port a custom ble service from sdk12 to sdk 14 and am a bit confused as to how to increase my uuid count. In sdk12 I did it like this:
uint32_t err_code;...
Hi
I am using wireshark 2.0.1(64 bit).When i am trying to capture the ble packets it showing error.I have attached the Wireshark error message.BLE Sniffer version 1.0.1.I...
In the Bluetooth Light Controller example for the client in main.c these constants are defined:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
Why...
Hi Nordic,
Sorry if I missed and repeated a question, just point me to the previous answer if it has been posted before.
I am trying the DFU example found in the SDK...
Hello,
I'm wondering that it is ok to route ANT line through board-to-board connector to chip antenna.
Because there is no space to place nRF52832 and chip antenna together...
Hi,
I've seen that SDK 12.3.0 contains a new version of the application sample using the Eddystone protocol for BLE. I would like to know if this version is compatible...
I am using the template example for S130(works fine).
I tried adding a simple Pin interrupt on the code but it didn't call the pin interrupt handler everytime I press the...
For applications using the application UART Module ) via APP_UART_FIFO_INIT() without hardware flow control - how does an application put the UART peripheral to sleep?
...
Hello Nordic staff (or anyone in the know),
I saw this post from @newtom almost a year ago which concluded that I2S master library does not support 32bit words from mics...
Hello there,
I am a beginner, i want to know what changes should i make in the already existing example "ble_app_uart" so as to make my nrf51 development kit able to transfer...
In the file app_sdcard.c of the SDK13.0.0, an assert is done when calling app_sdc_init() with a pin P0.0. Can i safely use P0.0 with the assert deactivated or should i use...
Hi;
I am using nrf51822 qfaa device with sdk12.3. I compiled eddystone example code and it worked with nrf51dk(nrf51422_qfac) board. Also, i have a board that has nrf51822_qfaa...
I would like to use the POFCON register thresholds to create a crude battery level indicator. I noticed that the POFCON register definition in the nRF52832 Product Spec has...
