I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I use BLE mesh github.com/.../nRF51-ble-bcast-mesh
but when I use the master control to write values to update the values of services, the following error occurs: "global...
Hi,
I have implemented the support for 'long write' as in
github.com/.../ble_app_hrs---LongWrite
which works from the MCP... except that on BLE_GATTS_EVT_WRITE, it seems...
I have bought nrf go starter kit with pca10005 board( nrf51822 ic). I want to program the nrf51822 using these tools.The guide that I got from the nordic website not explaining...
If the device is paired (but not bonded) using "Just Works", sd_softdevice_disable() causes the application to hang/crash (nothing happens until reset by watchdog timer)....
I want to generate 2 fast PWM waves with 25% duty cycles from nRF51822. They have same frequency of 4MHz but there is half a cycle delay between them. I checked the nrf_pwm...
Hi,
I am trying to get the NRF8001 rev. C chip working with a Tiva Lauchpad (TM4C123GXL) board. I modified the original Arduino SDK for use with Energia. I am using the...
Hello,
i want to write a global unsigned long variable in RAM after programming the device. The Use-Case is to set the clock value to the actual time. So the new unsigned...
I use BLE mesh github.com/.../nRF51-ble-bcast-mesh
but when I use the master control to write values to update the values of services, the following error occurs: "global...
Hi. All.
I am in the process of update SDK 9.0 from 5.2.
Meanwhile, SPI couldn't read from external flash's data.
Unusually SPI works well before infinite loop, I tested...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
I want to use the nRF51-DK board as a programmer for my target. As I understand it, this can be done with the signals on P19. However, there is one signal, EXT_RESET, that...
github.com/.../nrf51-UART-examples
Hey any I was trying to test the example, the one with BLE
I test
APP BLE sending --------shows on PC UART software
However, I can...
Hi,
I would like to ask if someone has experience using the AES. I n eed to be absolutely sure that the user SW can use the AES HW block for own custom usage. If yes, Are...
I'm using SDK's interface for AES ECB block, but getting a hard fault when ECBDATAPTR is redirected at ecb_data in the initialisation function:
static uint8_t ecb_data...
