Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Peripheral doesn't have any user interface that can be used for pairing and bonding but I want for my application is that the peripheral gets paired or bonded to the central...
I want to make one mesh beacon as a node of mesh network.
If one mesh beacon is a node of mesh network, I want the beacon broadcast the messages which in mesh network to...
I build some test project in Zephyr examples folder. (ncs\v1.5.1\zephyr\samples\basic\ND_test).
In additional I did some changes in the Zephyr project in drivers and added...
I have recntly purchased a Nordic Semiconductors nrf52840 development board. I am having issues with the J Link OB MSD. When connected to LINUX Ubuntu 20.04 LTS which is running...
Hi,
I am working on a bootloader that can do DFU for my nrf52840 DK. Currently, when the bootloader goes into DFU mode, it obtains the init packet via UART. Then, after...
Hi,
I'm trying to add the secure BLE bootloader(non debug, modified to run with S113, SDK 17.0.2) on a custom board with a nRF52810. I tried to DFU my main application(APP...
i working nrf52832 sdk 16 in that i want to use two uart?
actually nrf52832 have only one hardware interfced UART.but i try to implement two UART1 and UART2 in same program...
Hello,
I am working on an nRF52840 with S140SD chip.
I am currently using the RTT as a backend for logs. I tried adding the Flashlog backend in order to save the logs...
I'm developing with nRF52811 but firmware is developed for nRF52810.
I think there is no difference between them and that firmware should work well.
But SPIS doesn't work...
THis may have an obvious answer to an experienced embedded programmer but I do not qualify to be that. So I have a piece of working code that runs on the nRF52840 DK and it...
Can you use/link both nfc T4T and T2T libraries and wrapper/driver source in same application/build?
I don't mean emulating both modes at the same time.
Thanks.
To the kind attention of Nordic support team,
I have been using nRF ble sniffer successfully, it is a great tool. But I have some troubles when it comes to use it for ble...
Hi there!
I am placing variables in the ".non_init" section so that their values are retained across software resets. This works great if I only use an App + Soft Device...
I want to modify the uuid through the serial port. What variables can I use to describe this define? Is there any code for reference ?
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hi there
I'm currently using three different target platforms/boards #1 : a Nordic PCA10040 - attached to USB #2 : a UTO-NBL-52A developer board - attached to a J-Link plus...
