Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hello all
I was just following the thread launched by Alex concerning nrf 52 dongle driven from serial port, which is also very important to me, and now that thread is already...
Hi,
i would like to program my module nRF52840 via uart.
I generated private then public key using nrfutil.exe tool
i could programm softdevice and bootloader and...
I am trying to get the DCDC running on my custom NRF51822 board.
It is running but the results are a bit disappointing.
If I do a test and enable the TX with and without...
I've picked up a nRF52840 DK and dongle to do some testing with long-range beacons.
So far I think I have managed to configure my DK as a beacon in long-range mode (can...
Hi
I have a test mesh network, with several devices provisioned using nRF Mesh and.... a proxy node which has been provisioned using an alternative method but with the same...
Hi, I'm trying to make a SIG qualification Project. QDID97989 (nRF52 S132 V5.0.0) with replace PHY QDID97482(TaiyoYuden module). Launch Studio Project type is "qualification...
How to send and receive messages in ble mesh? The sending and receiving of sensor data I have done is not a switch value. I have tried many methods but failed.
I alredy run the assert tracking about 4 months ago on preliminary firmware.
Now I updated the modem firmware to v1.0.0 and compiled the last stable AT Client project from...
In the past we had a C based product that communicated from our Host processor over SPI to an nrf8001 peripheral using an Application Controller Interface (ACI) provided as...
Hi,
I am trying to set a fixed WiFi connection in the "/etc/wpa_supplicant/wpa_supplicant.conf " file, but it gets lost on every reboot. I assume it is because of the...
Hello everyone,
I've designed a device and I want to measure power consumption. Have you ever used a Power Profiler Kit for long-term tests for example one month? Is there...
To the kind attention of Nordic support team,
1) I was wondering if it could make sense to connect two nRF52840 boards (transmitting normal bluetooth RF signals) directly...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello, im using the ble blinky example and i want to send more information in the advertising paket. This example sends only the device name, flags and advertising address...
