NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hi,
For both (nRF52840 / nRF52832 ), with SDK version nRF5_SDK_15.3.0_59ac345
I am using Secure_Bootloader in the eample folder:
nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral...
I found an issue when using CONFIG_AZURE_IOT_HUB_DEVICE_ID_APP to set the Azure Device ID.
Around line 88 of azure_iot_hub.c the "user_name" structure is set using the...
Hi,
Is it true to say you have two modem firmware streams: 1.1.X and 1.2.X? Are these two kept in sync in terms of GNSS improvements? I notice the 1.2.2 release notes mention...
Hello,
I want to measure current consumption of nRF9160 of the Thingy 91 with the Asset Tracker application in PSM mode without GPS. For that, I added to the function modem_configure...
Hi,
Browsing the API I only saw Enhanced shockburst support. I need air compatibility to an old 250kBit plain Shockburst communication. No auto ACK and no auto retransmit...
I have run up the CLI example to test as we will require some command line interaction and why reinvent the wheel?
I run up the example with USB enabled and UART disabled...
Hello Nordic,
I try to establish communication between an ATmega328 based board an an Arduino Nano, so far without success. The goal is to improve a RF433 "Wire". 3 weeks...
Dear All, I am using the ADC to measure 3 voltages applied on different ADC inputs and 3 different channels. My ADC configuration looks like this: And this is how I am performing...
Hi,
I recently acquired the nRFgo starter kit and nRF2724 rev 2.1 and the nRFgo development kit. I have downloaded all of the supporting software that were found here...
I have the latest nRF Connect for Desktop.
After I install "nRF Connect SDK v1.4.99-dev1" in Toolchain Manager I don't have an "Open IDE" button.
I've tried uninstalling...
I am adding JLINK_MOITOR.c and JLINK_MONITOR_ISR_SES.s and add write
#if CONFIG_JLINK_MONITOR_ENABLED NVIC_SetPriority(DebugMonitor_IRQn, _PRIO_SD_LOW); #endif
at starting...
Hello everyone,
I'm trying to develop an application with BLE, using an example as a base.
The advertising is good, well configurated, I can edit manufacturer specific...
I am currently using Mesh SDK 4.2.0 and I could successfully write and read reliably from the flash using a second flash manager instance used in parallel with the flash manager...
HI，All:
the softdevice.hex has inlcuded the bootable/strat code,as the figure below ,how to separate the bootable code from the hexcode?
in the SEGGER IDE:
in...
