I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
I’ve not yet been able to successfully get an application (in this case Blinky) to complete a BLE DFU load and then execute. I’ve tried all the suggestions I’ve found in the...
Hello,
I would like to learn a little more about the possibilities of thin planning of connection events. I rely on chapter 15, in particular on part 15.7 of the S140 SoftDevice...
Hi, I'm trying to do the iot mqtt publisher example with the nRF5_SDK_15.3.0_59ac345, a nrf52840 and a Raspberry Pi 3 B+ as a gateway but I got some problems :
After the...
We have been testing the DK board and Thingy:91 and had a few questions on enabling PSM/queued mode.
We are able to enable queued mode for the lwm2m_client example on the...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi!
I'm going over the nRF52820 chipset, and I'm not sure I completely understand the reference schematics in regards to the LC filters on the REG1 DCDC enabled option....
I am using "ble_app_hrs_rscs_relay" example and modified it a bit by adding NUS service and FDS. Everything is working fine with mobile app and nrf dongle. How ever when I...
Hello,
I am trying to setup my project's architecture and I am trying to take advantage of some of the awesome libraries in the SDK. I am a bit confused on the differences...
I ran into an issue using RTT on recent SDKs: In SDK15.3 and up RTT stopped working in Segger Embedded Studio. Here's what I found in case others are having the same issue...
Hi,
We are having single Main supply VDD to nRF9160 SoC, which is powering both CoreM33 and Modem.
So this indicates Modem will be always ON when Core M33 is ON.
Is...
Hi everyone,
Following some tutorials as well some examples provided by SDK16 I was able to create a custom service with a characteristic that has read,write and notify...
Hi All,
I am using NRF5 SDK 17, I have been playing with several examples and noticed that when it comes set up, a peripheral or a priority or clock source there will...
I started modifying the NRF Android Blinky example project to suits my needs (to control a servo motor). I observed there is a BIG delay between writings to a specific characteristic...
