Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I'm evaluating possibilities of BLE-LESC Pairing/Bonding with the ble_app_hrs peripheral on the nRF52840-DK with SDK 12.3 and SoftDevice s132. To see what's going on in the...
Is it possible to flash multiple custom boards using sagger DKs at the same time?, assume 2 custom boards and 2 DKs, would they be able to flash the custom boards in parallel...
There are many places in the file fsm.c that have this compile condition check
#if defined FSM_DEBUG
blabla
#endif
that is wrong. The compiler will ignore it. There...
Dear Nordic,
Hello, I have to configure 2 UART. I have saw this post .
however, I have made a demo version for the project without 2 UART function, so I hope to apply...
Hello, I´m trying to compile the BLE Heart Rate service projects using SEGGER Embedded Studio. After importing the project from nrf52 SDK, I tried building the project but...
Hello,
I want to implement home automation project using 3 nRF52840 dongles. i.e I want to connect all the 3 dongles with each other and the signal sent from one device...
Hello, I am trying to design a product based on BLE MESH. I would need gateway to be able to accumulate data from network and send it outside. I need that gateway to connect...
Hi,
I have gone through the "ble_app_hids_mouse" example program. So far the program seems to work great, but how do we take control of the buttons since the function used...
Hello,
We have plan to use nRF52832-CIAA with external antenna connector (MHF4). I noticed that in 4-layer reference design layout there is quite big square keepouts on...
Hi,
I am using sdk 14.2.0.
i am using freeRTOS,created 3 threads.
all are running fine,but just for while(2 - 3 minutes).
after that, all the threads stoped.
may...
Hi,
I am doing OOB commissioning with OpenThread. According to section 10.12 of Thread 1.1.1 specification, Active / Pending Operational Datasets need to be persisted to...
Hello,
I'm trying to connect external RTC, which has a 32kHz clock on it's pin to nRF52832. So far I've had issues with connecting this clock to P0.00 pin and having P0...
Hi all:
when i add uart code in ble_multilink ,and it gived me errors like this:
"<error> app: Fatal error <warning> app: System reset <error> app: Fatal error <warning...
If I put too many characters into a serial using IRQ mode, it stops reading input.
I haven't tried polling or DMA yet.
Using
nRF5_SDK_15.0.0_a53641a
gcc-arm-none...
