Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi
I am having some issues with running QSPI on the nRF5340DK board. After I disabled the QSPI, I found the board still having a high current consumption of 700 uA.
Although...
Hello,
We use SEGGER_RTT_ReadNoLock() in our code, and this works perfectly. Our nRF is connected to a DK, which is connected to a computer.
However, when we compile with...
Good Saturday evening,
Up until now I’ve been accessing the registers directly in my Nano 33 BLEs to experiment with Timers, GPIOTE and PPI, all via the Arduino development...
Hello,
We're building zigbee devices around the nRF5340 with the nRF SDK/zboss/zephyr. I'm working on custom boards and have based my 802154 code around the samples in nrf...
is there a way to get more control over the auto ack feature of the 802.15.4 driver in zephyr?
I would like to ack frames without destination address only if nrf_802154_ack_data_pending_bit_should_be_set...
Hi all:
I have a software version that allows Bluetooth to be connected to the phone normally,
When I tried to use the SPI interface, it happened as long as I used
...
Hi there,
I'm trying to wire up a Uarte client to a Uarte server where the client device is an nRF9160DK, and the server is an nRF52840DK.
Connectivity between the cilent...
Hello,
My hardware guy asked me to look into whether or not we can use a fixed eSim (no card) with the 9160? If this is possible how do we program it with the particular...
Hi,
GOAL : I try to measure the current consumption in system off only.
PROBLEM : I measure a current of 8uA in system off while in the datasheet of the PAN1781 et nrf52820...
Hi, I accidentally marked one of my own replies as the answer.
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple...
Hello,
I am looking for an example that have the the ccs811 on the sdk15 but i didnt find it , I have found some driver ext like ccs811.h on the driver_ext file but I dont...
Working on a zephyr/zigbee/802.15.4 system and my code (loosely based on the Nordic samples) on a custom device was not behaving as expected.
So I broke out an nRF5340 DK...
Hello Devzone,
I'm writing to ask about how long a device running Nordic's aws_iot sample app (sdk-nrf 1.6.1 based, Zephyr 2.6.0 based) may be in a "radio idle" state, and...
