I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hello,
I am using nrf52840 dk and ses. I have written the code for hcsr04 ultrasonic sensor and I getting proper values but I want to send this data over bluetooth and I...
This is a very simple question:
According to the documentation, each dongle is assigned a Bluetooth Address at the factory using some random number generation algorithm...
Hello,
this question has been probably asked many times, but I could not find any good matches using the search.
My setup: I am using nRF52832, latest SDK 16.0.0 and a...
Hi everyone, We are doing a prototype with the nrf52840 module and I need to Certificate the board for RF emissions. I have some questions related this:
1- The BLE module...
Hi.. i am using nRF52832 ... 15.2 sdk Version. i'm trying to communicate between a central device and a peripheral.so if multiple peripherals are present and all of their...
1. I use buttonless DFU. As I understand it, at startup the bootloader checks CRC of the application, and if it is ok it jumps to it. So if I accidentally deploy an update...
I tried with the DK and my own USB-serial adapter and both fails at 1M with HWFC with this error:
nrfutil dfu serial -pkg bltest.zip --baud-rate 1000000 --flow-control 1...
Hi I would like to interface the nrf9160 with amw136 (silicon labs) module wifi.
The amw136 has the interfaces: serial (UART, remote terminal), SoftAP and WLAN client (concurrent...
i am working on nrf52832 DK, i am trying to upgrade my development kit firmware using mobile
and i successfully build "secure_bootloader_ble_s132_pca10040.hex " application...
I'm currently using this setup on a fitness device prototype that will send battery status, scores and relevant infos. RPi >>>RFM69 915MHz )))))) ((((( RFM69 >>> Adafruit...
Hi,
I am using the softblink library in SDK 13.1 to control a RGB status indicator LED. It works fine, until I want to change the PWM settings or the LED pin.
The change...
I'm developing an interface I2C to one sensor including SCL, SDA and open-drain return to know if
the sensor is ready to work. After Reset by "Build and Run" form Segger...
Hi,
I'm a new guy for the development in nRF52840 and try to build the application by using 802.15.4. I have two questions, as follows:
Firstly, when I follow the instruction...
Hi, environment is nRF5_SDK_16.0.0_98a08e2 windows SES target is nrf52840. I am using the nordic dev board. The final product is a wearable, which will connect to a smartphone...
Hi All,
I'm using NRF52832 for our product. I test bootloader functionalities with development kit. The software system is also tested separately by directly programming...
