Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
nodic example in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_lbs , ,i can not find the software interface place in peripheral_lbs example code from where to send
Hi.
I'm trying to make the i2cDevlib work on an nRF52 DK board.
There are several ports of the same to nRF51, and one to nRF25 but on the old SDK11.
I'm using SDK15...
Hello,
The Zephyr OS provides a function to reboot the module, sys_reboot(type) where type is either a cold or a warm reboot.
However I cannot find anywhere the difference...
Hello,
We opened from a clean download the example " ble_app_uart " in this folder:
\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
Hi, Community!
My development environment is the following:
SDK52,
nRF52840,
s140 17.2.0
nRF Sniffer
My problem is that I can not seem to be able to send more...
Hello,
We are working with the nRF52840 and the OTA works when I set 0x10001304 to a value from 0-3. When I set 0x10001304 to a value of 4 or 5, the OTA fails.
Hi there,
I'm developing with the nRF52840 right now.
I'm trying to read some sensordata with TWI. The sensors are BMM150, BMI270 and BMP388.
Unfortunately, I already...
Hi everybody,
I received a nRF52833 DK (PCA10100) and I was capable to install heart rate example dropping prebuilt hex into the mass storage driver. Later I flashed a led...
Hi
I have seen some queries for support asking if app_timer can be used for real time clock and calendar functionality,
i am using the nRF52810 but the answers were either...
Hi,
I'm very new to learn nrf52832. Recently, want to connect my NRF52832 device with pc, then , using the value uploaded from the device to draw a curve in pc' client....
Hello
I'm looking for API example to use Key Management Unit (key storage and key usage). But I didn't find it in all nordic documentation.
Could you help me to use KMU...
I am using the SDK 17.0.2 to make the advertisement and scanning for the two nrf52840 boards. One unit with extended advertisement only on channel 37 and the other unit scan...
The documentation says that: " By default, threads run in supervisor mode and allow access to privileged CPU instructions, the entire memory address space, and peripherals...
Dear Community;
I am trying to send some data via Lora with a nRF9160 connected with SPI to RF95W Lora module. The transmitter is a nRF9160 with a RF95W, and the receiver...
