Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
Dear Community;
I am trying to send some data via Lora with a nRF9160 connected with SPI to RF95W Lora module. The transmitter is a nRF9160 with a RF95W, and the receiver...
Hello,
We're piloting updating our sensor beacons RuuviTags to use Coded PHY for better range. The current design has nRF52832, our update would be to drop in a nRF52811...
Hi Nordic Support Team,
I am trying to combine
..\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_s140_ble\ses
and
..\nRF5_SDK_17.0.2_d674dde\examples...
Hi,
I have been looking around the forum and have found conflicting information regarding the existence of a QSPI flash driver and example for the nRF53 on Zephyr. Is this...
Hi,
I am trying to run nrf zigbee light bulb sample provided in the nrf SDK on the NRF52850 usb dongle.
I have sucessfully built "blinky" app sample with NRF Connect SDK...
Hello Everyone,
I am developing one product for the HVAC system. I have Radiator and STM's primary MCU. For development, I need to configure the thermostat cluster ID for...
Dear Nordic Community,
Because of unavailability of nRF52840 we are shifting the work to nRF5340. I have some queries on this topic as follows,
1) Is SDK will be changed...
Hi Nordic Team,
I am new to Bluetooth mesh and NFC. I am working with the device nRF5340 and SDK NCS v1.5.0 .
I have used the sample Bluetooth: Mesh light as a starting...
Hello, I'm trying to use PN532 module with nRF52840 using I2C. the data can be sent, but when it comes to read it, IRQ keeps high, so it reads 808080 .. I added a nrf_delay_ms...
Hello,
Starting with the example of mqtt_sn_client_publisher in the nRF5 SDK for Thread and Zigbee and I want to publish an array of data like this one
in a MQTT topic...
I am trying to send some data from nRF52840 to Xbee via Zigbee In this case, I set nRF52840 as router and Xbee is the coordinator. I use zigbee_cli_agent_router sample code...
Just took delivery of a new THINGY:91 from DigiKey - v1.4.0.
Trying to follow the steps in the User Guide, but when I plug into my Macbook, it's not showing up as a USB...
Hello,
I'm a CS student and I'm trying to work with nRF5340 DK. I'm trying to program the sample network_coordinator (Zigbee) to the board using SEGGER Embedded Studio,...
Hi,
I try to use the nRF sniffer but it can't capture any packets.
System used :
Windows 10 Pro x64
Wireshark 3.2.0
Python 3.8
nRF Connect v3.3.0 - Programmer...
Hi
I'm trying to config parity with UART, if I understand right even parity is supported.
In sdk_config.h
changing default value 0 to 14
#define NRFX_UARTE_DEFAULT_CONFIG_PARITY...
