I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello,
I am interfacing a NRF52832 with a PCF8574 I2C slave using SDK 15.0.0.
As per the datasheet, the device will send the data to the slave after it receives the write...
Dear Sir,
I designed a new pcb based on nrf9160,
The boards are populated with cipsim.
When running the MQTT_SIMPLE project i get the following error for the 2 boards...
Hi,
We are upgrading our product from SDK 15.0 to SDK 17.0.
In the old SDK there seems to be one file abailable: ../SDK_15/External/nrf_cc310/lib/libnrf_cc310_0.9.9.a...
Hello:
We are developing a DFU bootloader for an NRF52 product that supports USB and BLE upload methods (they are 2 separate bootloaders from a common source). Both work...
I am hoping to pass data from the nRF52840 to the nRF9160 over UART_0, on a custom PCB. For context, the aim is to pass data at a rather quick rate and good reliability. The...
HI,
I want to make a receiver to get BLE packets on any channel.(NO SOFTDEVICE)
I fail to fullfile it yet by reading <nRF52810_PS_V1.3.pdf>.
Any other hands can give...
Hi,
I am working on the asset_tracker application example on a Thingy:91 device. As I understand it, to activate the GPS it is necessary to keep the button pressed for a...
Hi,
In nrf9160 I want to check the communication of LTE device.
I have installed nRF Connect for Desktop, Getting Started Assistant, LTE Link Monitor, & Programmer.
...
Dear,nordic:
Please help me solve the exception encountered during the MQTT connection
SDK : ncs v1.2;
samples : asset tracker;
path : ncs\v1.2.0\nrf\applications...
Hello everyone a basic question but just to be sure.
I would like to make a custom board and I want to program this board with segger Embedded studio, should I just have...
Hi!
I managed to get the device connected to the nrfCloud and started receiving messages from it.
Anyway, the embedded antenna cannot catch the signal very strongly. Can...
Hi,
I am trying to test the asset tracker code on the nRF9160DK from the precompiled hex files from [ images_dfu_hex/nrf9160dk_asset_tracker_dfu_2020-04-29_bc7ade8b.hex...
It was my idea to compile the mqtt_simple vom v1.3.0.
I spend now one week with your sdk. I tried it with SES and also with command line. Absolutly nothing worked.
The...
I am using a nRF52840-PCA10059 dongle to acquire data at a high rate (between 50Hz and 400Hz).
The connection is very unstable, after some seconds of acquisition, it sort...
