Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello Nordic developers,
I have been unsuccessfully trying to use the extended ATT_MTU / DLE sizes for increased throughput on a nRF52832DK board running the Nordic UART...
Hi
I am working with nrf52 development Kit. Until now I have not worked with the whitelist advertising. I am using SDK v11.
I have a requirement initially I need to advertise...
Hello,
it seems the current nrfutils release assumes that the bootloader settings will be stored at address 0x7F000 on an nRF52.
However, unless I'm mistaken, that is...
Hi,
I have set up the Power Profiler as per the directions now on the step connecting the board to the Wiindows Python app it says "Cannot find calibration values" and the...
/* Copyright (c) 2012 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided...
Hello,
I am trying to program my BMD-300 using the NRF52-DK, below are my connections
BMD- 300 ---------> NRF52 DK
V Vtg
SWDIO SWDIO
SWDCLK SWDCLK
GND GND
The BMD 300...
Hello friends. How to write a number to and read from internal flash. My information about the microcontroller is very weak. I use STM32F103RET6 .
I test The following program...
Hello,
I am able to compile blinky with my SW tool set up, however, when I try to compile a more complex example (ant_broadcast_rx_pca10040_s212) I get issues with the...
Hi,
I hope is not a double post. I am doing a throughput evaluation with my custom board and an app that is based on the Nordic's Android UART app through NUS service and...
I am trying to get the ble_app_uart project to build in Eclipse for the PCA10036 nRF52 board. I have followed the Tutorial titled " Development with GCC and Eclipse" and successfully...
Hello,
i am stuck with this, trying to write to flash using pstorage module. Below is my code.
static void pstore_cb_handler(pstorage_handle_t * handle,
uint8_t op_code...
Hello,
I have downloaded the Hardware Files of nrf51822 smart beacon kit. But I Cant open the Altrium Designer Files (pcbdoc. files). Do u know how to open it or a program...
Hi,
I do test my project one central connect to 4 peripheral(HR and CSC).
and I put the memset(&m_ble_db_discovery,0,sizeof(m_ble_db_discovery)); err_code = ble_db_discovery_start...
Hi,
I use nRF52832 and SDK12.2
The Project is ble_central_and_peripheral and the link define is like below
#define CENTRAL_LINK_COUNT 4
Here will connect 1 HR device...
Hello,
Is it a good practice to modify SDK files?
I mean, do you use SDK as integral part of your project and feel free to modify it, or do you try to avoid it and just...
