Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
hello, When I switched from the NCSv3.0.0 version to the NCSv3.2.1 version, I encountered the following compilation issue. How should I eliminate this "Error 1 (Ignored)"...
Background: Our tests on SDK 2.5.0 showed that it was possible to maintain a Bluetooth connection at a distance of approximately 180 meters with the following initial advertising...
i am performing DFU process b/w nrf54l15 and nrf connect mobile_app ( Android ) and i am sniffing the it using nrf54840 soc and the bord is nrf21540dk in Wireshark i know...
Hi,
I am currently working with 2 nrf54L15-DK and a seperate 4 antenna array.
For my tests i run a 2x2 antenna config with preferred peer set to 1 and 4.
I was now...
I just got the board, installed the nRF connect sw. Then installed the J-link, connected the board, power it on and run the quick guide, but it searches and doesn't find anything...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
I'm running the nrf5340_audio_dk and using version 2.6.0-rc1. When connecting one NRF5430 as headset to another NRF5340 gateway, running BIS mode everything works fine. But...
Hi,
We've been working on an IoT device that uses an nRF52840 in a pre-approved module from Moko. We are getting ready for a commercial launch in 2026, but I am very confused...
I have noticed that the dts file includes the configuration for arduinio_spi, along with the corresponding pins associated with spi4. However, I am unsure about how to utilize...
The Bluetooth 6.0 Channel Sounding feature supports multi-antenna functionality. The nRF54L15-DK development board is currently single-antenna. Is there any official documentation...
Hello,
I am wondering how I can enable APPROTECT through UICR with a TFM project. Using ncs2.6.0 and nrf5340. My project makes use of TFM to separate secure and non-secure...
Hello,
I am experiencing an issue with the I2S interface on my nRF5340 DK while using the nRF5340 Audio Unicast Server application with the nRF Connect SDK v3.1.0. I am...
Hi,
I'm trying to test onomondo static profile with a custom board build with an nrf9161 chip. So I've followed onomodo readme, I got an error when i'm trying to build...
Hello,
Im worried i bricked my PPK2, as I had it in ammeter mode possibly reverse VIN/VOUT connections to my DUT.
The DUT is powered over usb externally. I tried to measure...
