I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
1.
I've been trying to get the lte_ble_gateway / let_sensor_gateway example wroking on the nrf9160dk v1.1.3. The example keeps failing at the No HCI driver msg. I...
Hi,
1. Check whether the nRF7000 supports setting the Radio test sample to Non-signaling mode TX test setup for packet generation
https://docs.nordicsemi.com/bundle/nan_046...
HI guys, I'm trying to figure out whether the problem I'm having is a hardware or software issue.
So, my problem is: I have created a custom board using the nrf5340 and...
We are facing strange issue we have this board https://www.raytac.com/product/ins.php?index_id=47
whenever we flash any firmware it works fine but if we erase from vs code...
I've made this following code with inspiration from the at_monitor example to test a custom board using the nrf9160 sip.
I get the following output:
When testing on...
Hi,
nAN_038 WLCSP Handling Guidelines V1.0.pdf does not support nRF52820 WLCSP
Please provide the WLCSP SMT data corresponding to nRF52820
Kind regards, Peter.Min
hello Nordic
i am working with two nrf52832 socs, with ncs v2.9.0.
I would like to know how many retransmissions occurred during a Connection Event in which specific NUS...
Hello,
I have a Xiao seeed nrf52840 and want to operate a peripheral IC over I2C. It doesnt have a driver so I'm following the developer academy on how to do raw I2C communication...
Hello, I am using the nRF Connect SDK v2.9.0. While working on the nRF52840 board, I used the library zephyr/crypto/crypto.h to perform AES/ECB encryption.
Part of the code...
Hi guys,
I'm a bit frustrated with the NRF Power Profiler II. I'm working on a low power project with the NRF52832 with a custom PCB and I decided to buy this power profiler...
Problem Description
I've implemented a W5500 Ethernet controller emulation for NRF7002 modules. While UDP socket sending works correctly, receiving UDP packets is problematic...
Hello there,
I was going through the Wifi fundamentals courses lessons in nordic academy and was using ncs 2.4 version, I was able to give it a build for one example,...
Hello,
I have gone through many devzone threads which suggest that Ble Mesh over coded PHY is not officially supported but, is possible. I am trying out the "Mesh" sample...
A pointer to the structure of mpsl_tx_power_split_t is passed into this function. I am not 100% clear on the documentation on this variable. The value returned from this is...
