Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Motivation: I would like to use SEGGER Embedded Studio V4.10 to use sample projects whose size is not available in keil(no license).
Problem: I can't check the operation...
Hi Team,
Can I automate BLE test cases using nRF52840 DK ? If yes what is the procedure to follow.
My DUT supports central role and I want to make nRF52840 DK as peripheral...
Hi,
we are in the pre-production stage and going for the final production release of our application code based on ble_app_hid_mouse example, in this stage I would like...
Basically the title. The documentation here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications/serial_lte_modem/doc/FTP_AT_commands.html
https...
I am using nRF52840 DK on VDD_HV. SW9 (nRF power source) set to USB and I am connecting a USB cable to J3 (nRF USB). SW6 is also set to nRF Only. My IC revision is QIAAD0...
Hi,
I tried to write firmware with nRF connect for Desktop and Programmer on Mac OS.
1. I installed nRF connect for Desktop 2.7.0 from github and J-Link driver (J-Link...
Hi,
I a have a firmware which was developed on a PCA10056 development board. We attached an external sensor which can produce an interrupt.
The interrupt is used to wake...
Hello,
I inserted the following line in the prj.conf file:
CONFIG_I2C = y
done this when I compile I have 7 errors in a code not added by me. the example I'm editing...
Hi,
We got a few boards that have large ADC error. I've already using nrfx_saadc_calibrate_offset to calibrate the offset so I suspect it's caused by gain error. The error...
Hello All,
SDK -- 15.3.0
I want to interface MX25r6435f with NRF52810 so i saw some older queries regarding this Flash driver,
so some where i saw that in sdk QSPI example...
Hi!
We are working with the nrf5340 (custom board-revision QKAAAB) and we are facing an issue when resetting the application. If we add some functionalities to a bluetooth...
hello,
i am using nrf52832 with sdk 15.2 and i want to advertise my beacon like the above picture how can i change the length type and values i can understand the app beacon...
Once paired & Bonding is completed. If neither side pairing & Bonding information is deleted. After restart the device is not advertising again. We are getting PM_EVT_CONN_SEC_FAILED...
Hi, Good afternoon. Some Questions.
1.
Is the Enhanced ShockBurst (ESB) protocol applicable to the nRF5340? I'd appreciate it if you could give me details on how to get...
The nrf52833_peripherals.h file has the P1_PIN_NUM set to 10 but the pca10100.h file has ARDUINO 8-13 pins mapped to port 1, pin 17 to 23. This cannot be correct and causes...
