Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi there!
I'm having an issue adding WiFi functionality to my project. I use the nRF9160DK and the nRF Connect SDK v1.5.1 on a Windows10 platform.
To keep it simple i...
I am using nrf52DK board as an observer to test my beacons. I have kept scanning enabled all the time (scanning interval & scanning window same), but the scan_evt_handler...
I want to use the nrf5x to develop the host/gateway of bluetooth mesh, may I ask which model is more suitable, which model currently supports the most mesh nodes?
And which...
Hi Nordic team,
I have successfully developed an application using nrfx (Timer/PPI/SAADC) combo in NCS 1.5.x to be able to sample 2x differential channels very fast.
Similar...
I have trouble developing BLE devices with Nordic NRF5280 and SDK 15.3.
I have a device that uses a custom BLE service, And when using nRF Connect on the mobile phone, all...
I have been developing some nrf52832 code (SDK 17.0.2) using the Segger RTT debug window for logging. I added the code from the UART example but the printf goes to the debug...
I'm planning to modify the nrf52832_ciaa reference designs in altium to emulate the functionality from a development kit and add an RTC.
I need access to pins P0.23, P0...
Hello. I would like to use an internal RTC to keep time going even if the power is off.
1. Is it possible to implement with 'nrf_calendar' module?
2. Should I think about...
I have a battery powered iOT device using BLE, I2C, and GPIO. I am focused on reducing the power consumption. When BLE is not connected, I want to have as little power usage...
This is in response to a central sending an update. I try and follow with the central's request except I set the times to the AUTO value. If I get an NRF_ERROR_NOT_SUPPORTED...
ran nordic blinky example on nrf52840 kit
Want to know where is the transmitter power set in the code.
refer any example where we can define transmit power
Hi Folks,
I am just asking general information (explanation and/or code samples examples) to set up a secured BLE connection between multiple centrals towards one peripheral...
Hi,
I'm programming a nRF52832 for SPI communication with another device which requires some single byte TX/RX. After a lot of head-banging, I realized that the nRF52 was...
Hello there,
if i download a hex-file to the NRF52840-Dongle with the J-Link (Lite) tool, the dongle always remains in bootloader mode (red led is flashing). But if i download...
