I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi,
we are developing a custom board based on nrf9160 that include CAN bus. When updating nRF Connect SDK from v1.4.2 to v1.5.0 we can not get CAN-bus up and running again...
Hello,
For our device we are using a NRF52832 and SDK version 17.0.2. It only has one Button connected to P02. Due to needing the device to be water resistant the decision...
I built the mouse BLE example .
In Windows 10 "Add a device" detects the Nordic_HIDS_mouse device and then issues the
challenge Press Connect if the PIN on Nordic_HIDS_Mouse...
Hi Everybody,
I am working on USBD keyboard.
I used USBD example for implementation.
I changed mouse profile to keyboard profile.
And it's recognized well without...
Is there a way to get the signals of the interrupt for a push-button/interrupt from the pin_change_int example in a logic analyzer software tool? Basically i'd want to visualize...
In bluetooth mesh only 3 channel are used.There is a way to use mesh with an extended number of channel.
Because in some industrial enviroments fading is very heavy and...
I was reviewing the silicon errata for Rev2 of the Nrf52840 and I found this.
[204] RADIO: Switching between TX and RX causes unwanted emissions
This anomaly applies...
I have a smart watch based on nrf51822.but i don't have the customer app.I download the nrf tool box can read the heart rate.But i don't know how to set or sync time,can someone...
Hi,
I have developed an app using OTA DFU support. Soft device used is S112.
is it possible to update Soft device through OTA DFU?
what is the max size of the image...
Hi , How can I connect arduino nano 33 ble with the application NRF Toolbox using Bleutooth when I program the arduino with segger embeded studio .
Please I need your help...
Hello:
After the nrf52 lost connection with the phone, should it go to the Directed mode of just start normal fast advertising. And what the differences between them?
...
Hi,
I just used the nRF Connect Toolchain manager to install the NRF Connect SDK. Then, the Segger studio keeps popping this error when I try to open a project:
And...
Hello,
From the nrf91dk datasheet, a stackup is provided. Because it looks custom, and I'm having a hard time finding a manufacturer that can do that stackup. What PCB...
hi，
I read the data manual of 52832, but I have some questions about the following parameters, like CM_FLASH,CM_FLASH/MHZ,CM_FLASH/MA,please explain it in detail and what...
