Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I am using Thingy 52 to measure the acceleration from accelerometer. I was expecting values like m/s2 but I am seeing values in unit vector, ie, values between (0 -...
I have nrf52dk (nrf52832) board and a custom nrf52805 board. The nrf52805 board has no external 32kHz crystals, but only 32MHz crystal. Also, it is in LDO mode (no DC-DC inductors...
Device nrf52832, nrf5_SDK_for_Mesh_v3.2.0_src with nRF5_SDK_15.3.0_59ac345
Hello.
I want to transmit and receive some data between smartphone app and mesh sensor.(almost...
Hi, Im using nRF52840 DK, Segger Studio v4.52 and SDK version 17. I have been trying to make BLE OTA DFU work but have had many problems along the way. I followed the guides...
Hi folks,
I need a production test of an nRF52840 module at PCB level. Our board connects near instantly with nRF Connect + Bluetooth Low Energy, and displays its device...
Hi,
I am trying to implement wireless power transmission. For sending output voltage information from receiver board
to transmitter board continuously which of you module...
Hi, I am getting link time error in segger when i building a pre-built library with zephyr for NRF5340.
Error says,
c:/gnuarmemb/bin/../lib/gcc/arm-none-eabi/8.3.1/.....
HI. I have modified "usbd_ble_uart" a little bit and have changed the BLE service for transfering the received data from USB over BLE. The problen is now, the BLE service...
I am working with the nRF52840 DK and was looking for a way to set a compare register to trigger at 300 ticks, and another to trigger at 40000 ticks. The register that triggers...
Hi,
I am a new comer so perhaps I made a mistake during project configuration.
I am using nrf Connect v3.4.2 on Windows.
I trie to add CC310 libray in sample hello_world...
The detected device could not be recognized as neither JLink nor BLE could be captured in wireshark, nor could the nRF Connect v3.4.2 - Programmer produce "Unsupported device...
Hi,
I am using NCS v1.3.0 for nRF9160. How to enable both BLE scanner and advertiser roles simultaneously?
Currently even I enable both, HCI LE set random address failing...
Hi. This is my first experience using Nordic Products and I have run into some issues trying to "Open nRF Connect Studio Project" from SEGGER Embedded Studio. I want to run...