Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi Nordic team,
we want to connect 2 nRF52840 based modules with Coded Phy S=8 Mode to make an cable replacement (NUS). MTU Size is 244 Byte ,to transmit cyclic 200 Byte...
I am trying to connect the DK to AWS.
I got the AT example working and uploaded the certificates. I managed to update the prj.conf file (and then took quite some time to...
It continue to give "No device available" when I connected thingy 91 to the nerf connect programmer app. I tried turning on device while keeping SW3 pushed but still not detected...
Hi Team,
We are planning use the crypto libraries for our application, just we want to know which library is best for us in terms of speed and memory consumption,
1. mbed...
Hi, I'm almost finished setting up a development environment for nRF52840 DK on macOS. I used the new Toolchain Manager to install everything, and then imported the "peripheral...
While developing our project using NRF9160 , we encounters a hard fault. The screen shot and the map file is attached. Please help us in understanding what is happening from...
Hi, we are using nRF52832 SAADC in differential mode. We have two channels connected.
Inputs are now configured as differential-N and differential-P (PSELP and PSELN). ...
Dear all:
i have a problem about connect distance. My central device is nRF52840 ，peripherals are nRF52810 device。all device Hardware RF performance are good. But,when my...
Hi In continue to Tzvi Kaplan thread and other threads here related to the PDM, like this one:
devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate...
Dear Team, SDK - sdk version 15.0.0 IDE - Segger Embedded Studio SOFTDEVICE - s140_nrf52_6.0.0_softdevice We are developing our custom application and it is battery operated...
Hallo,
I want to measure the RSSI of a BLE-beacon. The beacons runs fie, my problem is the other side. I read the thread:
https://devzone.nordicsemi.com/f/nordic-q-a...
Hi,
I am trying to make a project where one Bluetooth chip receives an audio file from mobile and another chip will receive it via serial communication and transmit ahead...
Will the nrf52811 I2C compatibility work with the I2C on the MLX90614 IR sensor. I need to make sure that they will work with each other without issue. Below is the datasheet...
