I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi, I am using nRF Connect SDK 14.0 with nRF9160 DK.
I want to use nRF52840 as a controller and nRF9160 as host. To achieve this, I flashed hci_uart sample on nRF52840 and...
Hello!
I move my device from nRF52811 to nRF52820 ( QDAA-C00 ) and I have a problem when using a comparator and TWI
If I configure TWI0 or TWI1 and use it with external...
Good day,
I am using a DK board with the nRF52832 (pca10040) and I am using a 4 kHz buzzer connected to the gpio 16. I have seen the examples pwm_driver and pwm_library...
Hi, I am using the Nordic nRF52832, with the Segger IDE（Nordic）, and v1.4.0 of theSDK, and would like to know how to enable both LLPM and Multilink.
I am starting from the...
Hi.
I want to ask about the Queued Writes module and the NRF_SDH_BLE_VS_UUID_COUNT. In the example ble_app_uart, in the "services_init(void)" function we initialize the...
Hi,
I'm having difficulties running the secure bootloader example (ble_debug version), it doesn't seem to be advertising or providing any logs.
I'm currently using the...
Hi,
I want to create a fresh project in Keil with nRF SDK as static library included into application. I have created the project, but when I run, the code always stuck...
Hi,
The error I get is as followed:
Output/Debug/Exe/Lesson10_Part3.elf section `.nrf_balloc' will not fit in region `UNPLACED_SECTIONS'
region `UNPLACED_SECTIONS' overflowed...
This is my third and final attempt at getting a custom nRF52 board to appear on my phone as an Adafruit Feather device. I have no issue with the genuine Adafruit hardware...
Hi! We're preparing a medical device and are evaluating nRF5340 chip. We'd like to know when the chip and PDK will be production ready i.e. when Development Kit for nRF5340...
Hi,
One of my customers is applying LWM2M to their target application.
And they are trying to fix LOCAL PORT of LWM2M.
I heard that when end equipment is registered...
Hello
I use nrf52832 and mpu6050. I am trying to obtain values for pitch, roll, and yaw using mpu6050.
I don't know if it's because there's no magnetic sensor, but there...
