Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi.
Hope you are well.
I want to send data from nRF51822 to nRF24L01+. I used the esb library to configure the nRF51 and I just change the settings as I want ( some settings...
Hello~ I have previously written related articles. But I don't get the answer I want, so I ask you again. Use the toolchain manager to use ncs 1.3.1. The error as shown in...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello guys!
We are workng with nRF52840 SoC and SDK v17.0.2.
Custom BLE Services and Characteristics are needed to implement in our device. Before starting that implementation...
Hi,
In our design, nRF9160 is powered by a LiPo battery, making VDD = 4.2V in a "fully charged" case, and VDD=5V in a "lipo is charging" case.
We would like to be able...
In trying to use a private key file to sign the application image I'm running into an issue with the PEM file. I created a PEM file using the following command:
as documented...
Hello colleagues,
Mi name is Daniel and i'm trying to develop a software application that let me calculate the PER (packet error rate) of a bluetooth transmission.
The...
Hello Team,
I am working on a project in which I want to used pdm microphone with nrf51822 xxAA and i am using keil u5.
1) So I have picked uart over BLE example from...
Hey there,
I am new to the community and I would like to looking for more than one cell. As I readed in another thread, it was possible with %NBRGRSRP a few month ago. ...
I was looking through documentation and I noticed that in OPS v0.7.1 the cold start was stated to be -144dBm. In PS v1.1 it calls out -142dBm. Can you explain why they are...
Hi!
I have BMD-350 -A-R and I want to program this by using SWD pins (SWCLK, SWDIO, GND Detect, and VTG) of Nrf52Dk . I make all the connections properly but for some reason...
Hi,
for evaluating purposes I'm trying to send quite big amount of data (100 kB) via socket interface. Sending proceeds fine until approximately 60 kB is transmitted. After...
Hi,
when powering up the nRF52840 PDK its interface MCU LED is blinking fast and the board is not recognized. I've tried to update its firmware by putting the board in bootloader...
On some android phones we have observed that if we try to scan using nRFToolbox for nRF51/ nRF52 controller advertising with UART they do not show up in the scan list. But...
Hello,
I am developing a wireless sensing device using the nRF24L01+ module and I'm planning to use a u.FL connector in my design. I can't seem to find any manufacturer...
