We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello! We are using the chip nRF52832 with the circuit recommended by Nordic Semiconductors, we want to implement the recharge of a battery by NFC. Without any data transmission...
Hi, I am trying to put nRF52832 in low power. My starting point is NCS v1.2.0 peripherial_uart app. When started I had ~300uA in idle mode, and that was because UART was always...
I've been trying to transfer a DFU update via serial, and I have gotten error 135 each time.
A colleague of mine got it working this january, with v3.1.0. Now, the same...
Hi,
1 - I don't understand why on the PCB layout example the track that is connected the L2 inductor is 762µm thick while the thickness of the pcb is 0.8mm?
2 - To have...
Hi,
We would like to know whether below programmers can be used to flash both NRF9160 application image and modem image. Also whether any command line support is there....
I'm using SDK 15.2 I'm trying to read two separate events configure in two separate pins ( PIN_1 and PIN_2 ) with two different handlers ( handler_1 and handler_2 ), like...
Hi
This is about missing information about current consumption for the GPIOTE peripheral in the v1.0 product specification for the nrf52840.
See section 6.10.5 it is empty...
Hi guys, I am trying to get Mobile network time and date using the NRF9160-DK 0.9.0 with the supplied iBasis sim card (in Switzerland) For this purpose I have executed the...
Hi !
I would like to implement UART on EVA board using MBN52832 SDK. Example usbd_ble_uart uses one UART for LOG printf. Please tell how to implement another UART on that...
modem fw v1.2.0 ncs v1.3.0 custom board
I'm trying to make a one-shot GPS app without assisted data by modifying gps sample app, and doing field test, but have an accuracy...
Hi, newbe here, using Segger Embedded Studios, two nrf52840 DKs, SDK 17.0.0, and a whole lotta enthusiasm! I am developing a custom solution based on the ble_app_uart (central...
Hi Nordic team,
One of our customer try to request the (T3324 = 2 secs) and (T3412 = 20 mins) but the +CEREG notification always return 11100000 for T3412 which is disabled...
Hello all,
I tested adc example code. And i want to change this code with our requirement. But in example code, i am getting alternate values on fixed voltage.
How can...
I continue to successfully upload the Blinkey app via DFU. However, when I attempt to upload my development app it does not start. From what I read it has successfully loaded...
