Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
I am trying to run the examples for the pc_ble_driver_py and I get some issues.
advertising.py says "board not found"
heart_rate_collector.py gives a calledProcessError...
Hi folks,
I want to do a project from scratch using the Segger compiler. Where can I find relevant documents with it. How can I make changes on the Blinky project? For...
Hello,
I have two version of Python 3.6 installed: 32 and 64 bit (Windows 10)
Recently i installed nRF5x command line tools (9.7.2) and pynrfjprog 9.7.1
For Python...
In zephyr many PPI has been employed in radio, and other PPI from 20 to 31 is pre-programmed channels and can not use by application. Do you have any plan for optimize this...
hello,
I have one problem to distinguish the following 2 functions :
ble_srv_is_notification_enabled and ble_srv_is_indication_enabled
in on_write function,
the two...
Hi Nordic
I saw the Dfu example.
BLE Secure DFU Bootloader and Buttonless DFU Template Application. I have two questions here. The boot loader and app distinguish a ram...
I'm getting a weird behaviour on my first NRF52 custom board. It's a BLE with HR, battery and a custom service. After programming I can test it properly with/without debugger...
Hi,
I am using SDK 14.0 on nRF52840 (DK), with sofdevice enabled and FreeRTOS port.
My question reagrds the "blocking mode" transfer - event handler was not provided...
I have four PCA10056 Development Boards and I downloaded the SDK for BLE Mesh. The examples, however, only work with the PCA10040 boards. I have tried redefining the board...
Hi all,
We are ready to have our product released and need to have it tested and certified for release in the following markets:
North America = FCC IC
Europe...
Hello,
I would like to configure the NRF51822 as a Peripheral to receive data from a smart phone, and then call a routine when the receive process has been terminated....
I'm using the nrf52832 and I need to stream audio from an SPI connected memory chip, to an I2S connected amplifier. Is there a way I can have the SPI device stream data directly...
Hello,
i have the following setup: nrf52 as peripheral, smartphone as central.
Peripheral's purpose is to be an interface between appliance and smartphone. It has no pairing...
Hello,
For more "simplicity" I have devised my own OTA update procedure. It relies on image information being embedded in a dedicated section (I have modified the linker...