We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Is it advisable to POT circuits using the nRF9151? If so, please advise of any precautions. The IOT product that I'm designing requires to be intrinsically safe. As such,...
Hello:
I am developing a board and shields based on nRF5340 (but this question is not really specific to nRF5340, it also applies to most other nRF5x chips). The main-board...
Dear Nordic Experts,
Hello,
i have defined a custom service containing a custom char. value in a peripheral according to https://github.com/NordicPlayground/nRF5x-custom...
Hello,
I am running into an issue when trying to use both GPIO and I2C peripherals on the same set of pins on an nRF54L15 board. I have an I2C bus configured on two pins...
I have two devices on TI CC2538 that having problems talking to the NRF52840 dongle.
The channel is channel 11
There are 8 devices using TI CC2538. Only two of them...
Hello,
I recently noticed that I may have an issue with our current design of PCB and firmware. We basically have created a datalogger using the nRF9160, and we take readings...
In the process of upgrading from SDKs 2.x to 3.x I either broke something or missed a step as the build process no longer produces a HEX file I can use for programming. My...
Hello,
After updating Visual Studio Code, I started facing an issue with the nRF Connect for VS Code extension. When I try to build my project, the toolchain is detected...
hi,
i'm learning exercise 1 and try to using step 14, i installed a java runtime environment and download cf-browser file but i can't open a cf-browser file on java(TM)...
Hi, I am using nrf5340 and nrf52840 SoC in my devices. I have tested that pairing works with the same linux machine for peripheral uart sample for nrf5340dk, nrf53 thingy...
Hi,
I am experiencing an issue with the nPM2100 I2C communication when using nRF Connect SDK 3.2.3. My hardware is a custom PCB with nPM2100QEAA and nRF52840QFAA
I am...
Hi everyone,
I am currently working with the nRF9151DK using nRF Connect SDK v3.2.3 (Zephyr OS v4.2.99). I am trying to run a basic UDP sample with a Terrestar Solutions...
Using the 54l15 chip, with the NCSv3.2.1 version, the example is compiled using peripheral_uart.
I have been using this environment for over a year now.
1. When I was...
