Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
In the datasheet of the nrf52840dk board, for the port P4, there are freely available pins p0.26 and p0.27. If I use those two pins in the overlay file, I am getting "Pin...
Hi there!
I'm trying to make an SH1106 screen working with my Zephyr 3.7.0 project using an nRF52DK (nrf52832-based one). My project is straightforward:
proj.conf
...
Hello,
I am attempting to use the DFU Target library to receive an update file over a custom protocol. I aim to do an MCUboot-style upgrade such that after the file upload...
Hi there,
My compiled image size in ROM is ~200kb.
I have 2 MCUboot partiitons, each 228kB.
I wanted to ask- is it possible for the application to use the second (non...
NCS v2.7.0
nRF52840 dongle
I want to program the nRF52840 dongle with external J-Link, and I can connect to nRF52840 dongle with SWD now. Using "nRF52840 Dongle nRF52840...
Hi,
I am evaluation PAWR feature and plan to use it for a product. The project is based on nrf5340.My enviroment is:
nrfconnect sdk v2.7.0
nrf5340 audio dk.
After...
Need to automate the FOTA process for devices with Zephyr build application which has mcuboot as bootloader, these devices can be programmed using nRF Device Manager and nRF...
I’m developing a product that uses the nRF9160 for LTE-M and the nRF52840 for Bluetooth. The nRF52840 is a pre-certified module, and I have experience with FCC compliance...
Is there any hardware limitations that would prevent one from using the nrf_802154 drivers on an nRF9161? If no, could you adapt the open-source sl to use the 9161 modem instead...
Setup: custom nrf9161 PCB, flashed with nrf9161 modem fw 2.0.1, using NCS 2.6.1
Targeting my custom board, I couldn't even speak to the modem lib, no IMEI etc.
So I dug...
Hello,
I have been trying to correctly setup my nRF Connect inside VS Code.
When I try to execute the command
west -V
in a nRF Connect window inside VS Code, I...
Hi i am using nRF52840 with segger embedded studio.
SDK -> nrf5-sdk 17.1.0 I want to configure rtc2 so that whenver i initialize it it should generate an interrupt after...
Hello, I am building a device which simultaneously advertises as a beacon and acts as a peripheral role device. Advertisements are sent at ~20 Hz with the connection to the...
hi:
I am use broadcast_sink and broadcast_source of nrf5340_audio simultaneously. use a button to switch source or sink. i am use NCS v2.6.2 if switch to sink mode is show...
