I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I have done a clean install of the SDK on Debian 13
I have nrfutil install and its working fine - i have tried installing both the v3.2.1 and v3.2.0 toolchains and in both...
Hello Nordic team,
We are using the GRTC on the nRF54L15 , and we are observing the following behavior:
When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
Hi, I am using nrf9151 as a modem running SLM. When SLM comes up, it throws this error. This is a new board run and 50% of the boards show this issue.
I appreciate there...
I am looking for a pairing between Windows laptop or Android mobile on the transmitter side and hearing aid which has bluetooth streaming features as a receiver..
I am looking...
Hi there,
Is it possible to have the DECT NR+ modem trigger events via DPPI? For instance, I'd like to capture a Timer value *exactly* when nrf_modem_dect_phy_time_get...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
Hi
We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below
The PDM DATA high level will decrease periodically
Is this waveform normal? If yes...
Hi,
I know that pc-ble-driver-py is archived but as there is no real alternative to it, I'm still using this package...
I'm using BLE nRF52840 dongle to connect to...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
# Background
I am attempting to install ble-sniffer onto WireShark for BLE sniffing. I have been following the guide in Link. I have already flashed my nRF52840 USB dongle...
Using Thingy:53, I needed to add the following code to the boards/thingy53_nrf5340_cpuapp_ns.overlay file in order to be able to view the output:
&uart0 {
status="okay...
Hi
We measure I2C SCL falling time is 5.87ns, little faster than spec. 6.54ns ( 20*1.8/5.5)
We use PIN_CNF[n] (Address offset: 0x200 + (n × 0x4)) ID D drive to tune, but...
Hello,
Are there schematics available for the nRF9151DK?
In the hardware ZIP file, I can only find the BOM and PCB files (PcbDoc and PrjPCB), but no schematic files or...
We are trying to understand whether it is possible to use our external flash drive at45db641e to implement DFU and then load the application firmware via Bluetooth. As far...
