Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hello,
I am following Lesson 9 Exercise 6 of the Dev Academy nRF Connect SDK Intermediate tutorials ( https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
SDK:nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_hrs\pca10040\s132_with_dfu\arm4\ble_app_hrs_s132_with_dfu_pca10040
Our product encountered a problem with DFU...
I use an nRF5340 and nRF7002 on a custom board. My firmware is stable on the nRf7002-DK, but crashes on my custom board most of the time (mostly when connecting to the Cloud...
I have an application with a shipping mode that when enabled/disabled calls `conn_mgr_all_if_connect/conn_mgr_all_if_disconnect`. These functions eventually end up in `lte_net_if...
Hi Nordic Support,
I'm having trouble getting my Onomondo or Conexa SIMs to connect to the network and would appreciate your help.
Device: Nordic Thingy91X (nRF9151...
We are running a custom board with the nrf52840 mcu on the legacy 17.1 nrf sdk. external flash IC is AT25FF321A
On a small portion of our boards (maybe 1 - 5%) we are noticing...
Dear Technical Support Team, I am currently developing with the nRF54L15-DK development board, using the official Nordic channel_sounding_ras_initiator example project.
...
Hello,
Our product has reached the final mass production stage, but we need to add a lock function to prevent erasure and access to the programming/debug port. nRF54L10...
I am using the nRF52833 DK and a Nordic-designed antenna array (12 antennas with 0.02m spacing) for an AoA Direction Finding project. I obtained the IQ data using Direction...
SW version :2.4.0 HW revision: nRF52833 development board, PCA20054 Direction Finding Antenna Board 1_0_0 I use the routine director_finding_central and director_finding_periopheral...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you.
I just want to explore on nRF52840 BLE section. I was not able to detect the device...
Hello! I have 126 kB MCUboot partition which I'd like to make immutable (write protected so it can't be corrupted). I have serial-recovery, KMU key handling, debug optimization...
When building applications/hpf/gpio with -DSB_CONFIG_HPF_GPIO_BACKEND_ICMSG=y on nRF54L15 DK (NCS v3.2.4), the build fails with error: '__device_dts_ord_DT_N_NODELABEL_ipc0_ORD...
Dear DevZone Team
To detect possible TWI slave devices connected on a TWI bus, we want to scan for device addresses and check if they are being acknowledged.
In the twi_scanner...
When a BTLE Connection is underway, calling bt_disable can result in an infinite hang in the Zephyr BTLE stack. Using ncs v3.0.0 Any ideas? There is some mention of: CONFIG_BT_HCI_ACL_FLOW_CONTROL...
