Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi Nordic,
I have 2 charac i can write, let's name it A and B.
When i write into A, it trig ble_A_on_ble_evt , BLE_GATTS_EVT_WRITE , no problem.
But w hen i write...
I started developing a project on nRF52. My task is to read the value from the light sensor (phototransistor).
The sensor is connected in this way:
my code:
init...
when i Use 2.4G radio to communicate with other modules,like cc2510, i have many questins:
1. as we known that CC2510 ' modulation format of the radio signal ,MSK is only...
Hi,
Maybe this is obvious, but I couldn't find the answer anywhere online. When I power my dongle from an external 3V3 source, can I still plug it in to my computer and...
Hi, during my tests, I use an NRF52 Dongle with the nRF-Connect app as a USB/BLE interface, but now I need to handle some custom data. I have seen that the dongle uses a COM...
Hi!
I'm working on using the SAADC in 14-bit sampling mode (oversampling set to x2) using nRF SDK 17. The supply voltage for my chip is 3.3V, and I have the reference...
Hi @ all, can anyone here recommend me a suitable chip antenna, preferably one with matching regulatory documents in combination with a nRF52840 MCU.
Thanks and best regards...
I am trying to flash a NRF52832 using the J-link EDU mini in the Arduino IDE but I am having no luck.
I have successfully downloaded... 1. J-Link Software and documentation...
While digging for electrical information I came across :
.63ma using HFINT or 1.58ma using HFXO ?
So I hunted down HFXO to see how to switch between them:
But nothing...
please advice how to add "QDEC_NRFX" to the project configuration of 5340
1. it's not on the default menu config
2. I have tried adding under "ncs\v1.4.99-dev1\zephyr...
Hello
I evaluated FOTA using the http_application_update example. This worked so far until I tried to use my own key for image signing. I created my own PEM-file using the...
Hello,
With nRF52840, I using SDK ver.16 to create a USB HID multiple touchscreen. I need to set up value some HID feature report. Such as Contact count maximum. I have...
Hi,
I want to configure the nRF52840 with Multi-role capability. I will be using the Central role as well as the peripheral role simultaneously. However, i'd like to maximize...
Hello
I would like to use SAADC 2 channels sample at 8K samples \ per second for each channel
based on:
https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
