Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi to everyone!
I am using nRF52832 driven by nRF52 DK and a sensor from Maxim Integrated. As debug output i am using the RTT viewer and as IDE Keil.
When i run my code...
Hello,
I am really new to nrf9160 product and its SDK. I want to send data from nrf9160 to an external flash memory. Could you please tell me how can I do this with SPI...
Hi
I am trying to open radio_test sample (ncs\v1.4.0\nrf\samples\peripheral\radio_test) for board nrf52840_nrf52811 but it fails - saying "Cannot create project"
Is that...
Hello, I am working on asset tracker from ncs 1.4.0 and on NRF9160DK when i try to concatenate doubles with snprintf it shows me nothing and returns a huge value (several...
I need to develop a product using the nRF910. I have downloaded files from the download page but when I expand the files to open they are LOCKED with a RED CROSS. How do I...
Hi DevZone,
Does anyone have any experience with performing a SD-Card format with the nRF52840 . This is to avoid removing the SD-Card from the hardware when a format...
Hi,
I tried programming the nRF5340PDK using the nRF connect programmer, but when I select the board I get the following log:
2020-11-11T13:04:58.307Z INFO Application...
Hello,
in our project we have a nRF52840DK as central and a BMD-300 (contains nRF52832 chip) as peripheral. The software on the nRF52840DK is based on the ble_app_uart_c...
I have a project where I am distributing code images to a number of devices with DFU (this is a custom bootloader)
The peripherals use a mixture of 52840 and 52811 SoC...
Hi,
I am currently using the nRF logging module to log data from a nRF52832-DK to my laptop via a serial connection. However, I would like to move over to BLE logging for...
I doing some basic antenna tests via RSSI and the logger output is quite important to me. So far, I managed to log my RSSI values and timestamp, as well as the ID of my devices...
hello Nordic
i am using nrf52832, sdk 16.0, s132 v7.01
i am scanning for ble beacon but i want to be able to change the filtered mac address (i still want to filter...
MCU: nRF 52832 SDK VERSION: 17.0.0_9d13099 SOFTDEVICE: 7.0.1 (s132)
I have an application with some custom services (4) with different characteristics number and behavior...
I was able to change the MAC address in the ble_app_buttonless_dfu example with "sd_ble_gap_addr_set( )".
But, when I enter the DFU mode, the MAC address changes to the...
Hello,
i am using nRF52832 Development kit.
and segger embedded studio for debugging
i have just started with NFC module. i run the NFC example "record_url" and it is...
