Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Dear all,
I have tried my best to find answers in questions posted previously but I still have a few questions that I would like to clear up. I will keep it concise. Thank...
I want to configure the UART1 (not the UART0), and I want to know if there have some examples that introducing the UART configuration by directing accessing the register....
Does Nordic have programming for the nRF52840 that enables both 802.15.4 and BLE, so the board can both become part of an 802.15.4 network and pair with a mobile device like...
Hi All,
i played with the /examples/dfu/secure_bootloader/pca10056_S140_ble_debug.
The application works fine so far.
I do have the following questions.
Is it...
Hi,
I am running into some problems with libuarte. I have two nRF52840-DKs talking to each other over UART. My setup is not ordinary however. The hardware configuration...
Hello -
We are developing a product for the nRF52840 using SDK v17.0.2 and FreeRTOS. Our application uses the RTC configured by FreeRTOS to implement a System ON sleep...
While installing the itsybitsy NRF52840 board from Adafruit in the Arduino IDE, I encountered the following error:
"Tool nrfjprog is not available for your operating system...
I can't get a button to work on a custom board; but same firmware HEX file on a different board works fine.
Using nRF5 SDK 17.0.2, SoftDevice S132 v7.2.0.
using a custom_board...
Hi,
I'm using an nRF52840 and I need to implement a driver in c for an external chip. The c driver is written, and I only need to add specific functions regarding the SPI...
I can't see the answer, so I will write it again.
hello.
nrf24l01p(ptx), nrf51822(prx)
nrf24l01p set
TX_ADDR = 0xA5B300
EN_AA = 0
EN_RXADDR = 1
SETUP_AW =...
Hi, I am trying to add Buttonless DFU functionality to the ble_app_blinky example.
The process I took
1. added the following files to the project
ble_dfu.c ble_dfu_bonded...
Hello, I am trying to implement a basic BLE connection between the nRF52840 Dongle and an Android Device (nRF Connect). I wanted to secure this BLE connection with a passphrase...
Hi everyone,
I am working on buttonless OTA DFU. I have generated my own private and public keys using nrfutil and created the .zip file for DFU.
While generating the...
Using the following image UUID on NRF51822, how do i connect to the host in the nRF5_SDK_12.1.0_0d23e2a softdevice? I used to the example of ..\ble_peripheral\ble_app_uart...
