We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
On the nRF54L15, is it possible to configure MCUboot so that the secondary image slot is stored in external flash connected via the SQSPI interface instead of internal flash...
Hi,
We're looking to integrate the NPM1304 in a product with a very small battery. As per the NPM datasheet we've selected a battery with a PCM.
We've previously seen...
We have a production system based on asset_tracker_v2 in V1.7.0 and V2.5.0. it normally connects and publishes fine 24/7. we have many sensors in the field. There are time...
Hello Nordic team,
I have a retail Thingy:91X device. IMEI: nrf-359404230239544
It connects to hello.nrfcloud.com, but I cannot add it to my own nRF Cloud account because...
We currently have a self-developed development board with NRF5340. The example program uses Bluetooth transparent transmission. Now I have added a GPIO pin: en_power is set...
When I was running the dm process of Connect SDK 3.0.2. I wanted to make one device as the initiator and six devices as the reflectors. I expect that the reflectors will not...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hi,
We have developed a custom board with both nRF52833 as the BLE beacon and nRF7001 as WiFi. We have chose to use patch antenna with UFL connector for both. When we tried...
Hi,
I have now run most of the YAML test successfully on the Matter TH and while I usually need to restart the TH between runs it seems fairly reliable now. Before sending...
Hi experts, I'm using the example under nrf-bm/samples/bluetooth/ble nus, and I've configured prj.conf, but it's not working.
I've been struggling with this for ages...
I am getting an error trying to get coded phy working with a sysbuild configuration for a nrf5340 custom board:
I am trying to follow the Bluetooth: Peripheral Heart Rate...
Hi,
I am using the nRF5340 for my project.
In the production stage, I am facing an issue: after programming the nRF successfully, when I perform a readback, it shows...
We have a Python script that is using pylink to open an RTT session and send some commands to the Firmware.
We have tried the JLinkRTTClient to send and receive command...
I’m working on reducing power consumption in my application using the LIS2DW12 sensor. I am currently turning off its LDO to cut power during low-power periods.
The problem...
Could you please help with providing terminal plating information for nRF52833? I have it noted as Sn but want to check if that’s matte or bright Tin.
Thank you,
Be...
