I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi There,
This is Particle's Sr. Hardware Engineer, Ping. We are working on a SoM (System-on-a-module) called EG91-SoM that with a nRF52840 (Thread) + EG91 module for acting...
Hello,
Hardware: NRF52840, Development Software: any
I am hoping to generate 3, or ideally 4 separate (independent duty cycles) PWM signals at a frequency of at least...
I use sdk13.0,s332,when my system working,it will auto reset about 129 seconds per time,I make a breakpoint,find it caused by "softdevice_fault_handler",when it reset,the...
Hello,
I am starting development on what should be a straightforward application using the nRF52832. It is actually this BLE module , which contains the nRF52832. However...
I am wondering if I could have access to a mechanical drawing or 3D model of the N RF52840-DK . Does anyone know where I could find either of these?
Thanks,
Julia
I am trying to understand why my program is returning this error (NRF_ERROR_RESOURCES). I read through a lot of other posts in the devzone and tried replicating them, but...
My board is nRF52840 + S140 + nRF5_SDK_15.2.0_9412b96, my configue as below picture and file "ywk_bsp_ble.c" .
When nRF Connect APP connect my device, it alway be disconnected...
Hello,
I am using nRF52832 (BT832 module designed by fanstel) based module for my application. we have developed customized PCB using the module. while evaluating the...
What chip supports Open Thread? SDK and softdevice versions supported?
We are in evaluation phase looking for potential radio manufacturers for an upcoming project.
Any...
I see similar posts, but no answer of this problem. I have similar code that work on my FW, but when I port it to my BSL, advertising is not working and when I look at return...
I am migrating from SDK11? to SDK15.3 and noticed nrf_drv_common.c is no longer available and has no replacement although nrfx_common seems to have replaced nrf_drv_common...
Hi, what are the (security) implications of running bootloader with #define NRF_BL_APP_CRC_CHECK_SKIPPED_ON_GPREGRET2 1 in production code? We use sdk15.0.0 with secure dfu...
Hi everyone,
I have an issue with power consuption. I work with the SDK15.2.0 and the SoftDevice S140 on a custom board.
I launch the ble_app_pwr_profiling example on...
I wasn't receiving any log messages while debugging the ble_app_uart_c example using SES so I enabled appropriate logging functions and set them to level 4 in config.h. Still...
