We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
DEVICE_MANAGER_APP_CONTEXT_SIZE should be less than 256 bytes in size.
However, it seems to work properly (not fully tested) whith a size of 800 bytes, and no more...
Hi all,
I want to make sampling from microphone at 16KHz. So I want to first disable softdevice, do all measurements. An after that enable softdevice to transmit data. Will...
Hi,
Recently, I am playing around with the NRF51 dongle and trying to make it work as a BLE master.
However, when I run the sample code(e.g. advertising, multi-link .etc...
Hello, i am seeing a strange behaviour of pstorage module and i don't understand what is happening. I have read links below:
pstorage-problem-on-power-off
saving-data...
Hi,
I haven't been able to find a clear answer to this.
With the ESB protocol, a payload can be stored in the PRX TX FIFO to be sent back to the PTX as part of the ACK...
I have some nrf51422s beacons and wondering if they can send and receive data. So I want it to keep transmitting its id and signal strength but if somebody is reading the...
I am trying to implement the ANT+ Environment Profile using the nRF51 DK and I was wondering if anyone had done this and could point me in the right direction to start. I...
how to synchronize multiple NRF52 them?
Should I use a router? What route do you recommend for development?
Otherwise many people tell me that the Bluetooth has a very...
Hi all,
I create 4 timer in APP, and there seem only one timer (work in single shot mode) can not trigger by right ticks.
I add some log and find that:
First I...
Noticed in ant_parameters.h
#define MAX_ANT_CHANNELS ((uint8_t)15)
First question: is this correct for nRF51?
Second question: is nRF51 going to support 15 channels...
Sorry for the newbie question -- I am new to programming microcontrollers.
I would like to know if it is possible to program the nRF24LU1+ to behave like a USB host? I...
Hi!
Is this correct scenario to minimize battery usage for radio tag transmitting 8 byte packets at 3 Hz?:
setup:
turn LFCLKSRC on with CLOCK_LFCLKSRC_SRC_Xtal...
Hi all, i am trying to start using the smart beacon kit nRF51822, but searching around i am a bit confused on how to flash the most recent softdevice with sdk on it; i followed...
I'd like to do the same thing :
how to use dm_device_delete
nRF51822 S110 v8.0.0
nRF51 SDK v10.0.0
DEVICE_MANAGER_MAX_BONDS=2
I test Nexus5, Nexus7, iPad...
