Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
When following the unit test example, and even with an alternate minimal implementation, I get the following error:
PS {nRF Connect terminal} > west build -b nrf52840dk...
To people who might be interested in this ticket
I'm trying to make a WiFi connection using the nRF7002 chip. It is a custom board based on STM32 chip. My question is, is...
example:ble_app_uart+ esb_timeslot SDK17.1 Hi Recently our product (PRX) received poor esb communication. I caught through sniffer that when PTX sends a message, our device...
Hi, I have gone through Lesson 4 in Wifi fundamentals. But exercise 1 fails to compile. I have also tested to compile the solution-project, but with the same result. There...
When I look at eh graphic .overlay, I see that the UART0 is there, but no node is assigned. Is there a Node for a two wire UART Driver with no flow control? Peripheral only...
Hello,
I bought a new USB keyboard and since i can't detect anymore Nordic Devboard as nRF5380. No device detected on Visual Studio Code, and on nRFProgrammer neither. ...
Hi,
I working on a project where i measure the distance between nrf52840 dongle and nrf52840 dk using multi carrier phase difference method.
Now, i want to display the...
Hello.
I'm currently trying to send AT Command using an external MCU or USB to UART to check LTE on the NRF9160. The board I use is the nRF9160DK. I changed the pins of...
HI,
I have two solar panes for my project 3W 5V and 2 W 9V. I would to measure current of the panels with the Power Profiler II.
I think this should work (my calc is 3W...
Good Evening!
We are designing a project using BLE; however, it requires quite heavy processing. We are still at a low level with pure C to save power, but the MCUs offered...
Hello,
Looking for potentially a better way of un-provisioning a provisioned mesh node. My nodes are provisioned via NFC, tag data containing UUIDs & OOB data. After the...
I work nRF52840 + nRF5 SDK(S140 v7.2.0)
If I call sd_ble_gap_connect() for a DeviceAddress of an already connected device, what will be the result?
What will be the error...
I am currently developing with the nRF9160DK and nRF7002DK. My project is to use the nRF9160DK as an external MCU to control the nRF7002DK's wi-fi and BT like a module.
...
This issue is exposed, or exacerbated, by our ongoing project of trying to upgrade from NCS 2.3.0 (Zephyr 3.2.99) to NCS 2.6.1 (Zephyr 3.5.99).
In our product, we emit log...
Our projects don't need all the repositories fetched by the default nrf/ncs manifest.
Is it possible to use a custom manifest repo or manifest file while installing the...
