Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I am really new at working with Bluetooth and the various protocols contained within.
I am using SDK 17.0 and drivers 2.7. I am working on a DK-52 board.
I am working...
The TWIM peripheral allows you to tx multiple buffers back-to-back like this:
- Set buffer 1 in TXD.PTR, TXD.AMOUNT - Trigger TASKS_STARTTX - Wait for EVENTS_TXSTARTED ...
Hi,
For testing purposes, I need a copy of the spec that the Nordic UART BLE service adheres to. Ex. minimum capabilities, mandatory functionality and attributes, etc. ...
Hello,
I tried enabling the Zigbee shell, through RTT, in my application and when that failed I built and burned the nrf/samples/zigbee instead, slightly modded to get rid...
Hi All. My task is simple. I want to implement LE secure connections on DFU. I have seen the ble_gls example. It has a passkey for bonding, I am looking into that too. I ran...
I have a repository that is intended to be used by other repositories via ZEPHYR_EXTRA_MODULES. This seems to be working fine. However, now I'm trying to add some code to...
I am evaluating a front end module by skyworks 66111 output power is ~14dBm. The FEM requires that logic dictate when to transmit and when to receive. When CRX, pin 17, is...
HI
we have developed our custom board using nrf5340. We are using NCS v1.7.1 for application development. I can't able to flash the HCI_rpmsg application to the network...
Dear Sir or Madam,
I would like to establish Bluetooth communication. When the Central is connected to the Peripheral, I want to measure the RSSI value of each data channel...
I wanted to add this info to my previous ticket, but there was no option to reply. Just an FYI, here is the link:
https://devzone.nordicsemi.com/f/nordic-q-a/84225/expert...
I have the following: - NRF52840 - BG96 modem - NCS 1.5.1 - Zephyr v2.4.99-ncs2
When I start the firmware, it will first bootstrap followed by leshan server registration...
There already exists a question in the DevZone regarding this error but a lot of time has passed and maybe there is already a solution out there.
Basically, I want to execute...
Hello I have been able to run the lvgl sample in the nrf9160dk, however this only works when built in a secure board, when build in non secure a bus fault occurs. Using the...
All of our wireless products over the past 10 years have used the nRF24L01 or nRF24L01+. In order to minimize latency for our time-critical communications protocol, we are...
