Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
After configuring the options for an nRF project, segger studio cannot create the project by warning me the error: "create_nordic_project.py failed"
The problem seems to...
I'm trying to make MQTT publisher example work using a BMD-340 evaluation board and nRF5 SDK for Thread and Zigbee 4.1.0 . I'm using a Raspberry Pi 3B with a Raspberry Pi...
Hi,
We have been using the MQTT sample code with a few iBasis SIM cards for some time without issue. This week we made a test where the mqtt_disconnect function in the sample...
I got the BLE mesh SDK from: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
I want to develop a mesh gateway to connect...
Dear friends,
We plan to develop a mesh gateway, however, i found the SDK only offered a mesh serial example which based on python, but our platform can't support python...
I have an nrf52832 DK, which when on, constantly obtains and sends accelerometer data from an IMU to whatever BT device it is connected to. I also have an nrf52840 Bluetooth...
Hi,
I just want to add SPI to my BLE project to read some data from my gyro , but after spi's addition, the code doesn't work normally anymore. I print a log in the cycle...
Hello
i'm use nrf52840 and I want write external qspi flash over BLE DFU but cannot be use
how can i solve this problem?
DFU log
modified nrf_fstorage_sd...
I'm building a project for the nRF52832 using the NRF5-SDK version 14.0.0. I'm compiling using GCC 6.3.1 ( arm-none-eabi-gcc (GNU Tools for ARM Embedded Processors 6-2017...
Hello,
We are using the AWS library on a Thingy91 to enable FOTA. We have a working example where we store the bin file in S3 as instructed in the SDK documentation.
Now...
Hello, I am trying to use the Peripheral UART code with the nRF9160-DK. I followed this guide https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started...
Dear All, I was wondering if you could provide any examples or advice as to good practice techniques when using the Watchdog timer in a multi-threaded Zephyr application.
Hi all,
I'd appreciate some help on the following problem:
I'm trying to put a custom hardware into a low power sleep mode from which I want to wake up regularly. I’m...
Hello
I am doing a project need to implement firmware update from the application
and I reference bellow thread,
https://devzone.nordicsemi.com/f/nordic-q-a/68368/write...
