Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am trying to use nrfsniffer to debug connection related issues.
We have a ble connection between central and peripheral and we are sending status updates to the peripheral...
I am building an application nrf52840 SDK v17.0.2 soft device is S140 with Segger embedded studio.
Application is to send advertisement data in one single channel (say channel...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.0.2 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using nRfgo Studio to:
Erase all
Program the new Soft Device...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.2.0 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using "nRfgo Studio" to:
Erase all
Program the new Soft...
hello,
i am using nrf52840 in our customised board and i am getting this error while debugging the application
4<debug> nrf_sdh_ble: RAM starts at 0x20004230 <error> app...
Hi all,
Debugging via RTT in Segger Embedded Studio stops working after DFU, however if I connect via JLinkExe + JLinkRTTClient I can still interact and debug via RTT.....
Greetings,
I am currently using nRF5 SDK 16.0.0, Softdevice s140_nrf52_7.0.1_softdevice.hex, and Mesh SDK 4.2.0. I migrated all my code base from nRF5 SDK 15.3.0, Softdevice...
Is there a way to obtain context on when a particular BLE transmission ends
RADIO_STATE_STATE_TxDisable == NRF_RADIO->STATE
An by context I mean to know what handle was...
Hello all i want to do a task that is control another LED using ble_app_blinky. In the ble_app_blinky project a characteristic is used to control an onboad LED. I have connected...
Hello
I have a custom board with nRF52840 and have migrated from TWI legacy driver to nrfx_twim. Im trying to communicate with accelerometer and gyroscope chip. With legacy...
Hello forum,
I have a new project that requires Bluetooth connectivity and I think that the nRF52805 suits me best due to its very small size.
The nRF52805 would work...
Hi, I would like to test sample bluetooth code ( ex: central) with nrf5340 dk, what's the difference between central for cpuapp and cpunet ? which one i have to load , cpunet...
I am trying to read Manufacturer Specific Data from a non-connectable advertisement packet from a pressure sensor.
I followed the example in https://devzone.nordicsemi.com...
I have used the nrf9160 development board and it can works rightly. But from this week, it doesn't work. I can download my code to the board, but it doesn't work. When I press...
