Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Using: ncs v1.4.0, Modem FW v1.2.3, SES v5.10d
I have a custom nRF9160 board with code based on the Asset Tracker app. I have GPS triggering off of the accelerometer. GPS...
The PDK does not show up in file explorer. Power switch in VDD position. LED 1 is on solid. The device manager universal Serial Bus controllers does not list any device that...
Hi, sorry for adding more posts on the same issue, but I don't see any of the posts that speaks to my current situation. I'm using nRF51822 and SDK 12.3.0, and I'm trying...
I am using NRFSDK 1702. I have one NRF52840 as central and multiple peripherals. The central receives data from the peripherals and then transmit the received data via hardware...
Hello,
I am trying to create an application that uses the mesh light lightness [client/server] model using the example application as a guide and I have a few questions...
I want to check which version of BLE is implemented while using a particular SDK or Soft Device(SD). Is the version of BLE dependent on SDK or SD or both ? I couldn't find...
Hi,
We encountered a problem if we take off the battery during functionning.
The UICR Register is completly erase when we put back the battery.
The issue is with lost...
Hi - I have a MDBT42Q SoC board developed by Seeed Studio which contains the nRF52832 SoC. The board is powered as the image below and I can program the board through the...
SDK: nRF5SDK Toolchain: ARM GCC
Hello,
I have some devices out in the field using nRF52840s, using the non-SoftDevice bootloader, and a custom mechanism for reading updates...
While the nRF5 SDK offers great support for validating the SoftDevice and application firmware in internal NOR Flash on every boot, it looks like that's not the case for the...
I am using nrf52 DK board with SDK15.3.0 developing my application on top of ble_blinky_peripheral example .
How do add CTS service in my application ??
I have refered...
Hi
I want to make use of this SD-card reader together with the nRF9160dk.
From what I understand:
1. I need to create a nrf160dk_nrf9160ns.overlay file to chose which...
Hi,
As in the subject, I cannot find where to change the optimisation level. I am working with the Zephyr bluetooth sample project - peripheral_hr.
I have found a previous...
Hi
I have register the esim of iBasis and its works relly well but I need know how to use a esim of a different company on nRF9160DK, I don't know if the location is important...
